24/08/2023 04:43:19

스터드 - 범프 스톱 - 램프 캔 - LH(수리)

교정 코드 10102118 0.48 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
유럽만 해당: 디이소시아네이트 작업에 대한 훈련을 받고 모든 필수 인증 과정을 완료한 기술자만이 우레탄 및 디이소시아네이트가 포함된 기타 제품을 사용하는 절차를 수행할 수 있습니다. 디이소시아네이트가 함유된 제품으로 작업할 때는 적절한 개인 보호 장비(PPE)를 착용해야 합니다.
  • 1460222-00-B - BUMP STOP SOCKET
  • 1014689-00-A - MOLYKOTE M-77 PASTE
  • 1820212-00-A - BOLT, PANHEAD, M6X16

Repair

  1. Remove the LH tail light. See 테일라이트 - LH(탈거 및 장착).
  2. Remove the damaged LH liftgate stop stud from the LH lamp can panel.
  3. Measure the diameter of the hole on the LH lamp can panel that was created after removal of the liftgate stop stud.
    Informational PurposesAn informational icon, calling your attention
    참고
    The diameter of the hole must not exceed 10.5 mm (0.43 in). If the hole is larger, then the panel should be replaced.
  4. Apply a shop towel behind the LH trunk side trim carpet.
    Informational PurposesAn informational icon, calling your attention
    참고
    Position the shop towel under the LH lamp can panel to catch metal shavings that are created in the next step.
  5. Drill out the LH lamp can panel.
    Informational PurposesAn informational icon, calling your attention
    참고
    Depending on how much rust is present, drill out the hole on each lamp can panel with a 6.5-10.5 mm (1/4 - 13/32 in) drill. Try to remove as much rust as possible but do not exceed 10.5 mm (13/32 in).
  6. Apply masking tape around the hole on the LH lamp can panel.
  7. Sand out any remaining rust on the LH lamp can panel.
    Informational PurposesAn informational icon, calling your attention
    참고
    Clean with an IPA wipe afterwards and allow 1 minute to dry.
  8. Apply self-etching primer onto the LH lamp can panel.
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend to use a brush to apply primer to prevent paint overspray on the body panel when primer spray is used.
  9. Allow the primer to dry for 5 minutes, and then apply a second coat of primer onto the LH lamp can panel.
  10. Allow the second coat of primer to dry for 5 minutes, and then apply a third coat of primer to the LH lamp can panel.
  11. Remove the masking tape from around the hole on the LH lamp can panel.
  12. Install the LH rear bodyside tail light to the vehicle. See 테일라이트 - LH(탈거 및 장착).
    Informational PurposesAn informational icon, calling your attention
    참고
    Install new gaskets to each taillight mounting bolt (x2) and the taillight electrical connector housing (x1).
  13. Apply approved structural adhesive on the slotted pan head screw
    Informational PurposesAn informational icon, calling your attention
    참고
    Apply structural adhesive only on the inner side of the head of the screw. Avoid contact with the thread. Refer to the Model 3 Colliision Repair Manual for Approved Structural Adhesives, see .
  14. From the inside of the lamp can panel, install the slotted pan head screw onto the LH lamp can panel.
  15. Install the LH trunk bump stop (torque 1.5 Nm).
    Informational PurposesAn informational icon, calling your attention
    참고
    Apply a light coat of Molykote M-77 on the stud.
  16. Remove the shop towel from behind the LH trunk side trim carpet.
  17. Install the LH trunk side trim carpet.
  18. Install the trunk garnish onto the body.