09/10/2024 00:30:27

액추에이터 - 블리드 - LH(히트 펌프)(탈거 및 교체)

교정 코드 18102212 3.30 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

경고

이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

Raise and support vehicle
Open hood

참고
Press "Open" button on touchscreen to release latch, Lift lid manually
Remove rear apron

참고
12x clips, Only store rear apron visible face upwards
Remove cabin intake upper duct assembly

참고
3x clips, Some configurations may come with 4x clips
Remove closeout panel from frunk assembly

참고
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Grab closeout panel from bottom then pull it upward to release clips, Disconnect switch
Remove bolts securing frunk assembly

참고
7x bolts, 10mm, 5 Nm, Lift up RBN covers to access upper fasteners, Newer vehicles may not be equipped with covers
Remove frunk assembly from vehicle

참고
12x clips, Replace any clips if broken or missing, Number of clips may vary on older vehicles
Remove RH wiper arm nut cover

참고
1x cover
Disconnect washer hose from RH wiper arm

참고
2x clips, 1x hose, Disconnect Y-tube fitting and release washer hose clips
Remove nut securing RH wiper arm to wiper module

참고
1x nut, 15mm, 25 Nm
Remove RH wiper arm and hose assembly from vehicle
Remove LH wiper arm nut cover

참고
1x cover
Disconnect washer hose from LH wiper arm

참고
2x clips, 1x hose, Disconnect Y-tube fitting and release washer hose clips
Remove nut securing LH wiper arm to wiper module

참고
1x nut, 15mm, 25 Nm
Remove LH wiper arm and hose assembly from vehicle
Remove LH shock tower cover

참고
2x push clips
Remove RH shock tower cover

참고
2x push clips
Release cowl screen from windshield and remove from vehicle

참고
2x push clips, 6x clips
Remove fresh air intake assembly

참고
2x studs, Maneuver between cowl and frunk
Remove the bolts securing wiper module

참고
3x bolts, 10mm, 7 Nm
Disconnect wiper module harness

참고
1x connector, Do NOT place limbs within the linkage movement area as wiper arms will automatically transition to parking mode
Remove wiper module from vehicle
Release harness clip from LH side of washer tank inlet

참고
1x clip
Remove LH front wheel center cap

참고
1x cap
Loosen LH front wheel

참고
5x nuts, 21mm, 175 Nm
Raise vehicle partially and lower lift onto locks

참고
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
Remove LH front wheel

참고
5x nuts, 21mm, 175 Nm
Partially remove LH front wheel liner

참고
6x clips, 1x bolt, 10mm, 5 Nm, Newer vehicles may be equipped with 2x push clips securing lower portion of liner to body
Remove lower bolt securing washer tank to vehicle

참고
1x bolt, 10mm, 3 Nm
Partially install LH front wheel liner

참고
2x clips, Partially install LH front wheel liner, Wheel liner will be removed again later, Install 2 clips to secure LH front wheel liner
Install LH front wheel

참고
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool, Torque at later step
Lower vehicle until tires are touching the ground

참고
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Remove upper bolt securing washer tank to vehicle

참고
1x bolt, 10mm, 3 Nm
Disconnect washer pump and level sensor connectors

참고
2x connectors
Remove washer tank from vehicle

참고
2x connectors，Keep washer tank upright to keep contents from spilling
Remove vehicle from lift

참고
Recommend assistance to push the vehicle backward, Note this vehicle can only be safely pushed for a very short distance and at very slow speed
Connect to vehicle using Toolbox 3.0

참고
Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle, https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)If RJ45 ethernet diagnostic connector present connect directly from laptop using an RJ45 Ethernet cable
Enter EPB Service Mode through toolbox 3
참고
Select ‘Actions’ tab and search for 'EPB Enter Service Mode', Select PROC_EPB_X_SERVICE-MODEvia Toolbox: (link)via Service Mode:
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
via Service Mode Plus: Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brake, select 'Both' and 'Start', click 'RUN', Hold down brake pedal while performing routine, Caution vehicle may roll freely, Select ‘X’ at top right of window to close once complete
Enter EPB Service Mode through toolbox 3
참고
Select ‘Actions’ tab and search for 'EPB Enter Service Mode', Select PROC_EPB_X_SERVICE-MODEvia Toolbox: (link)via Service Mode:
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
via Service Mode Plus: Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brake, select 'Both' and 'Start', click 'RUN', Hold down brake pedal while performing routine, Caution vehicle may roll freely, Select ‘X’ at top right of window to close once complete
Enter EPB Service Mode through toolbox 3
참고
Select ‘Actions’ tab and search for 'EPB Enter Service Mode', Select PROC_EPB_X_SERVICE-MODEvia Toolbox: (link)via Service Mode:
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
via Service Mode Plus: Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brake, select 'Both' and 'Start', click 'RUN', Hold down brake pedal while performing routine, Caution vehicle may roll freely, Select ‘X’ at top right of window to close once complete
Remove laptop from vehicle

참고
Do not close Toolbox 3.0, we will need to resume later
Push vehicle away from lift

참고
Recommend assistance, Place wheel chocks to keep vehicle from moving, Note this vehicle can only be safely pushed for a very short distance and at very slow speed
Open all four doors

참고
If vehicle is being powered down, Latch rear doors to prevent accidental closure
Lower all four windows
Move LH front seat forward
Remove console lower rear panel

참고
5x clips, Insert the plastic trim tool with a 90 degree bend at the bottom of the cover and pull straight out to release
Remove LH rear exterior bolt from center console

참고
1x bolt, 10mm, 7 Nm
Move LH front seat backward
Remove LH front floor mat
Remove LH console side panel carpet

참고
12x clips, Use trim tool starting at rear edge to release upper clips, then pull bottom to release remaining clips
Remove LH front exterior hardware from center console

참고
2x bolts, 10mm, 7 Nm
Move RH front seat forward
Remove RH rear exterior bolt from center console

참고
1x bolt, 10mm, 7 Nm
Move RH front seat backward and seat back downward
Remove RH front floor mat
Remove RH console side panel carpet

참고
12x clips, Use trim tool starting at rear edge to release upper clips, Pull bottom to release remaining clips
Remove RH front exterior hardware from center console

참고
2x bolts, 10mm, 7 Nm
Power off vehicle from center display

참고
Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
Disconnect 12V negative terminal

참고
1x nut, 10mm, 6 Nm, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
Disconnect first responder loop

참고
1x connector, Release locking tab
Disconnect harness from rear of center console

참고
1x connector
Disconnect USB harness at right front of center console

참고
1x USB connector
Remove center console from vehicle

참고
Recommend assistance, Tilt rear of console upward, pull assembly towards rear of vehicle, then tilt front of console upward and remove through passenger side
Remove LH IP end cap

참고
3x clips
Remove LH mid A-pillar assembly

참고
1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
Remove LH air wave bezel cap from main decor assembly

참고
2x clips, Newer vehicles are equipped with solid bezel.
Remove LH upper A-pillar trim

참고
3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
Remove clip for LH lower A-pillar trim

참고
1x push clip
Remove LH lower A-pillar trim

참고
2x clips, 3 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
Remove screw and clips securing LH footwell cover

참고
2x push clips, 1x screw, T20, 2.5 Nm
Remove connectors from LH footwell cover and remove from vehicle

참고
3x tabs, 1x Ethernet connector, 1x puddle light connector, APAC specific vehicles have an additional OBDII connector that will have to be disconnected
Remove fasteners securing driver knee air bag to vehicle

참고
1x push clip, 2x screws, T20, 2 Nm, 4x patch bolts, T30, 8 Nm, Newer vehicles have 4x patch bolts, E10, Discard after removal, Support the knee air bag while lowering, The connector / harness length is very short
Disconnect the driver knee air bag and remove from vehicle

참고
1x connector, Release locking tabs, Then release squib from air bag, Support air bag while disconnecting, Connector release may vary
Remove the LH footwell duct from HVAC module

참고
1x push clip
Remove RH IP end cap

참고
3x clips
Remove RH mid A-pillar assembly

참고
1x clip, 1x tab, Release upper clip then pull mid A-pillar upward to remove from vehicle
Remove RH air wave bezel cap from main decor assembly

참고
2x clips, Newer vehicles are equipped with solid bezel.
Remove RH upper A-pillar trim

참고
3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
Remove clip from RH lower A-pillar trim

참고
1x push clip
Remove RH lower A-pillar trim

참고
1x clip, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
Release RH footwell assembly from IP

참고
4x push clips
Remove RH footwell assembly

참고
2x connectors
Remove bolts securing passenger knee air bag onto vehicle

참고
4x patch bolts, T30, 8 Nm, Discard after removal, 2x screws, T20, 2 Nm, 1x push clip, Newer vehicles have 4x E10 patch bolts
Remove passenger knee air bag from vehicle

참고
1x connector, Release locking tab, Connector release may vary
Remove main decor assembly

참고
15x clips, Entire decor does not need to come off for glove box removal, If you lift RH side of decor then you will have access to 3x torx screws securing top of glove box, Replace securing clips as needed
Disconnect glove box USB cable from car computer

참고
1x connector, Depress latch on top of USB cable to release internal latches, then release from car computer
Remove screws securing glove box assembly to IP carrier

참고
6x screws, T20, 2.3 Nm
Remove glove box from IP carrier

참고
3x clips
Disconnect glove box assembly connectors

참고
3x electrical connectors
Remove passenger footwell air duct

참고
1x push clip
Remove RH IP air wave duct

참고
2x push clips
Disconnect RH upper duct thermistor from RH IP air wave duct

참고
1x connector
Release driver air bag assembly away from steering wheel

참고
2x spring clips, 3x datums, Press the spring simultaneously from two access holes to release, Access holes located at 4 and 8 o’clock position, Do not insert tool too far as air bag connector could be damaged
Remove driver air bag assembly

참고
1x connector
Disconnect steering wheel

참고
1x connector
Remove bolt securing steering wheel to steering column

참고
1x patch bolt, 10mm hex, 80 Nm, Discard after removal, Counter hold the steering wheel when breaking bolt loose
Remove steering wheel from steering column
Pull upward to release steering column upper shroud from lower shroud

참고
4x clips
Remove upper screws securing lower shroud to steering column

참고
2x screws, T20, 1.5 Nm
Remove lower screw securing lower shroud to steering column

참고
1x screw, T20, 1.5 Nm
Remove lower shroud from steering column
Remove SCCM from steering column

참고
1x bolt, 5mm allen, 9 Nm
Disconnect steering column control module (SCCM) assembly connector

참고
1x connector, Remove retaining clip on the connector, release connector, then remove the remaining broken clip from connector, Discard retaining clip after removal, Originally installed clip is black, Replacement clip is orange
Remove SCCM from steering column

참고
1x bolt, 5mm allen, 9 Nm
Release IP service panel from IP and disconnect temperature sensor connector

참고
4x clips, 4x tabs, 1x connector
Remove bolts securing center display to IP carrier

참고
Vehicle may be equipped with either: 2x patch bolts, T30, 12 Nm or 2x patch bolts, 10mm, 16 Nm, Discard after removal, Slide towards rear of vehicle to remove
Remove bolts securing housing neck to center display and slide away from display

참고
2x bolts, T30, 3 Nm, Number of fasteners on older vehicles may vary
Remove retaining clip from display connector

참고
1x clip
Disconnect harness connector from center display

참고
1x connector
Remove center display from vehicle
Remove center display neck housing from vehicle
Remove screws securing LH side of IP brow finisher

참고
4x screws, T20, 2.3 Nm, Fastener count may vary, Older production vehicles may have 5x screws
Remove screws securing RH side of IP brow finisher

참고
4x screws, T20, 2.3 Nm, Fastener count may vary, Older production vehicles may have 5x screws
Remove IP brow finisher from vehicle

참고
16x clips, Need to lift top pad up slightly to insert trim tool and release clips, Then slide IP brow finisher towards rear of vehicle
Pull RH side of RH air duct out and release from IP

참고
1x screw, T20, 2.3 Nm
Disconnect harness connector from RH air duct and remove duct

참고
1x connector
Pull LH side of LH air duct out and release from IP

참고
1x screw, T20, 2.3 Nm
Disconnect harness connector from LH air duct and remove duct

참고
1x connector
Release clips securing defroster grill

참고
8x clips, Replace any damaged clips
Pivot rear edge of defroster grill up and release tabs from IP

참고
6x tabs
Remove screws securing LH speaker to IP and remove speaker

참고
3x screws, T20, 2.3 Nm, 1x connector
Remove screws securing center speaker to IP and remove speaker

참고
1x connector, 3x screws, T20, 2.3 Nm
Remove screws securing center tweeter to IP and remove speaker

참고
1x connector, 2x screws, T20, 2.3 Nm, Discard tweeter and screws after removal
Remove screws securing RH speaker to IP and remove speaker

참고
3x screws, T20, 2.3 Nm, 1x connector
Disconnect connectors for passenger air bag assembly

참고
3x connectors, 2x connectors for regions other than North America, Connector release may vary
Remove bolts securing passenger air bag assembly to cross car beam

참고
4x patch bolts, T30, 8 Nm, Newer vehicles have 4x E10 patch bolts, Discard after removal
Remove screws securing IP carrier to cross car beam near passenger air bag

참고
2x screws, T20, 2.3 Nm
Remove screws securing IP carrier to cross car beam on lower LH side

참고
2x screws, T20, 2.3 Nm
Remove screw securing IP carrier to cross car beam on upper LH side

참고
1x screw, T20, 2.3 Nm
Remove screws securing IP carrier to cross car beam at lower center

참고
2x screws, T20, 2.3 Nm
Remove screws securing IP carrier to cross car beam at upper center

참고
2x screws, T20, 2.3 Nm
Remove screw securing IP carrier to cross car beam on upper RH side

참고
1x screw, T20, 2.3 Nm
Remove IP carrier from cross car beam

참고
Recommend assistance. Be cautious to clear the harness clipped at top center of HVAC assembly, This will also ease removal, Remove IP carrier through passenger front door
Remove screws securing driver air wave duct to cross car beam

참고
2x screws, T20, 2.3 Nm
Disconnect LH upper duct thermistor from drivers air wave duct

참고
1x connector
Remove driver air wave duct from HVAC assembly
Remove headliner harness clips on LH lower a-pillar

참고
2x clips
Disconnect the headliner harness connector from LH lower a-pillar

참고
1x connector
Disconnect the dash connector from the left body controller

참고
1x connector, Release locking tab and gently pull down to release connector
Disconnect the HVAC connector from the left body controller

참고
1x connector
Disconnect IP harness connector from electronic steering column

참고
1x connector
Release the IP harness clip located on the blower motor assembly

참고
1x harness clip
Disconnect blower motor connector

참고
1x connector
Release clip securing center speaker harness to HVAC assembly

참고
1x clip
Remove LH center display bracket

참고
2x bolts, T30, 12 Nm
Remove RH center display bracket

참고
2x bolts, T30, 12 Nm
Remove bleeder duct adapter from HVAC assembly

참고
4x clips
Remove nuts securing steering column to cross car beam and carefully lower steering column

참고
4x nuts, 13mm, 15 Nm
Remove bolts securing cross car beam to LH side of bulkhead

참고
2x bolts, 13mm, 25 Nm
Remove bolt securing LH cross car beam bracket to cross beam

참고
1x bolt, 13mm, 25 Nm
Remove the nut securing the LH cross car beam bracket to body

참고
1x nut, 13mm, 25 Nm
Remove LH cross car beam bracket from vehicle
Remove clip securing LH front main carpet to cross car beam

참고
1x clips
Remove bolt securing RH cross car beam bracket to cross beam

참고
1x bolt, 13mm, 25 Nm
Remove nut securing RH cross car beam bracket to body

참고
1x nut, 13mm, 25 Nm
Remove the RH cross car beam bracket from vehicle
Remove clip securing RH front main carpet to cross car beam

참고
1 clip
Remove bolts securing the cross car beam to HVAC assembly

참고
4x bolts, 10mm, 5.5 Nm
Remove bolt securing the cross car beam to HVAC assembly

참고
1x bolt, 10mm, 5.5 Nm
Loosen bolt securing cross car beam to upper cowl

참고
1x bolt, 13mm, 25 Nm
Remove the bolts securing the LH cross car beam to body

참고
2x bolts, 15mm, 29 Nm
Partially remove bolts securing RH cross car beam to body

참고
2x bolts, 15mm, 29 Nm, Leave a few threads of RH cross car beam bolts installed inside body of vehicle, This will avoid cross car beam from falling
Disconnect LH bleed actuator

참고
1x connector
Partially remove LH side of cross car beam

참고
Recommend assistance, Use caution not to damage the interior
Remove bolts securing LH bleed actuator to HVAC assembly

참고
2x bolts, 6mm, 2.3 Nm
Remove LH bleed actuator from HVAC assembly

장착

Position LH bleed actuator to HVAC assembly for installation

참고
Align guide and push LH bleed actuator toward HVAC assembly
Install bolts securing LH bleed actuator to HVAC assembly

참고
2x bolts, 6mm, 2.3 Nm
Install cross car beam into position for installation
Connect LH bleed actuator

참고
1x connector,
Loosely install bolts securing LH cross car beam to body

참고
2x bolts, 15mm, 29 Nm, Torque at later step
Loosely install bolt securing cross car beam to upper cowl

참고
1x bolt, 13mm, 25 Nm
Loosely install bolt securing cross car beam to HVAC assembly

참고
1x bolt, 10mm, 5.5 Nm, Torque at later step
Loosely install bolts securing cross car beam to HVAC assembly

참고
4x bolts, 10mm, 5.5 Nm, Torque at later step
Position RH cross car beam bracket to vehicle for installation
Loosely install the nut securing the RH cross car beam bracket to body

참고
1x nut, 13mm, 25 Nm, Torque at later step
Loosely install bolt securing RH cross car beam bracket to cross car beam

참고
1x bolt, 13mm, 25 Nm, Torque at later step
Position LH cross car beam bracket to vehicle for installation
Loosely Install the nut securing the LH cross car beam bracket to body

참고
1x nut, 13mm, 25 Nm, Torque at later step
Loosely install bolt securing cross car beam to LH cross car beam bracket

참고
1x bolt, 13mm, 25 Nm, Torque at later step
Install bolts securing cross car beam to LH side of bulkhead

참고
2x bolts, 13mm, 25 Nm
Torque bolt securing cross car beam to upper cowl

참고
1x bolts, 13mm, 25 Nm
Torque bolt securing the cross car beam to HVAC assembly

참고
1x bolts, 10mm, 5.5 Nm
Torque bolts securing the cross car beam to HVAC module

참고
4x bolts, 10mm, 5.5 Nm
Torque bolts securing the LH cross car beam to body

참고
2x bolts, 15mm, 29 Nm
Torque bolts securing the RH cross car beam to body

참고
2x bolts, 15mm, 29 Nm
Torque the nut securing the RH cross car beam bracket to body

참고
1x nut, 13mm, 25 Nm
Torque bolt securing RH cross car beam bracket to cross car beam

참고
1x bolt, 13mm, 25 Nm
Install clip securing RH front main carpet to cross car beam

참고
1x clip
Torque the nut securing the LH cross car beam bracket to vehicle

참고
1x nut, 13mm, 25 Nm
Torque bolt securing LH cross car beam bracket to cross car beam

참고
1x bolt, 13mm, 25 Nm
Install clip securing LH front main carpet to cross car beam

참고
1x clip
Position the steering column for installation
Install the nuts securing the steering column to cross car beam

참고
4x nuts, 13mm, 15 Nm
Install bleeder duct adapter to HVAC

참고
4x clips
Install the RH center display bracket

참고
2x bolts, T30, 12 Nm
Install the LH center display bracket

참고
2x bolts, T30, 12 Nm
Install clip securing center speaker harness to HVAC assembly

참고
1x clip
Connect blower motor connector

참고
1x connector
Install blower motor harness clip to HVAC assembly

참고
1x clip
Connect IP harness connector to electronic steering column

참고
1x connector
Connect the HVAC connector to the left body controller

참고
1x connector
Connect the dash connector to the left body controller

참고
1x connector, Fully seat connector and pull release tab into locking position
Install headliner harness clips to lower a-pillar

참고
2x clips
Connect headliner harness connector

참고
1x connector
Install driver air wave duct into HVAC assembly
Connect LH upper duct thermistor to driver air wave duct

참고
1x connector
Install screws securing driver air wave duct to cross car beam

참고
2x screws, T20, 2.3 Nm
Install IP carrier onto cross car beam

참고
4x mounting tabs, Recommend assistance, Slide mounting tabs on IP carrier into brackets on vehicle, Be cautious to clear the harness clipped at top center of HVAC assembly, This will also ease installation
Install screw securing IP carrier to cross car beam on upper RH side

참고
1x screw, T20, 2.3 Nm
Install screws securing IP carrier to cross car beam at upper center

참고
2x screws, T20, 2.3 Nm
Install screws securing IP carrier to cross car beam at lower center

참고
2x screws, T20, 2.3 Nm
Install screw securing IP carrier to cross car beam on upper LH side

참고
1x screw, T20, 2.3 Nm
Install screws securing IP carrier to cross car beam on lower LH side

참고
2x screws, T20, 2.3 Nm
Install screws securing IP carrier to cross car beam near passenger air bag

참고
2x screws, T20, 2.3 Nm
Install bolts securing passenger air bag assembly to cross car beam

참고
4x patch bolts, E10, 8 Nm, Install new patch bolts
Install connectors for passenger air bag

참고
3x connectors, 2x connectors for regions other than North America
Install RH speaker to IP carrier

참고
1x connector, 3x screws, T20, 2.3 Nm
Install center tweeter to IP carrier

참고
1x connector, 2x screws, T20, 2.3 Nm
Install center speaker to IP

참고
3x screws, T20, 2.3 Nm, 1x connector
Install LH speaker to IP carrier

참고
3x screws, T20, 2.3 Nm, 1x connector
Position defroster grill and lower tabs into position on IP

참고
6x tabs
Secure clips securing defroster grill

참고
8x clips
Position LH air duct into IP and connect harness connector

참고
1x connector
Install LH air duct into IP

참고
1x screw, T20, 2.3 Nm
Position RH air duct into IP and connect harness connector

참고
1x connector
Install RH air duct into IP

참고
1x screw, T20, 2.3 Nm
Install IP brow finisher into vehicle

참고
16x clips, Need to lift top pad up slightly to slide IP brow finisher into position
Install screws securing RH side of IP brow finisher

참고
4x screws, T20, 2.3 Nm, Fastener count may vary, Older production vehicles may have 5x screws
Install screws securing LH side of IP brow finisher

참고
4x screws, T20, 2.3 Nm, Fastener count may vary, Older production vehicles may have 5x screws
Connect RH upper duct thermistor to RH IP air wave duct

참고
1x connector
Install RH IP air wave duct

참고
2x push clips
Install passenger footwell air duct

참고
1x push clip
Connect glove box assembly connectors

참고
3x connectors, New puddle lamp harness routing prevent blocking movement of pawls, Make sure harness is routed properly above passenger footwell air duct before connecting
Install glove box into IP carrier

참고
3x clips
Install screws securing glove box assembly to IP carrier

참고
6x screws, T20, 2.3 Nm
Connect glove box USB cable to car computer

참고
1x connector
Install passenger knee air bag onto vehicle

참고
1x connector, Use caution not to damage connector and harness, Support knee air bag while connecting connector
Install bolts securing passenger knee air bag to vehicle

참고
4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 1x push clip, If vehicle equipped with T30 bolts update to E10
Install RH footwell assembly onto IP

참고
4x push clips
Position center display neck housing into vehicle
Position center display into vehicle
Connect center display

참고
1x connector
Install retaining clip to center display connector

참고
1x clip
Slide down neck housing and install bolts securing neck housing to center display

참고
2x bolts, T30, 3 Nm, Number of fasteners on older vehicles may vary
Install center display to IP carrier

참고
2x patch bolts, 10mm, 16 Nm, Install new 10mm patch bolts, Slide towards front of vehicle
Connect temperature sensor connector and install IP service panel into IP

참고
4x clips, 4x tabs, 1x connector
Connect steering column control module (SCCM) assembly connector

참고
1x connector, Install new orange retaining clip to connector then install SCCM connector, Perform push-pull-push to make sure connector is seated properly
Install SCCM onto steering column
Install SCCM onto steering column

참고
1x bolt, 5mm allen, 9 Nm
Install lower shroud onto steering column
Install lower screw securing lower shroud to steering column

참고
1x screw, T20, 1.5 Nm
Install upper screws securing lower shroud to steering column

참고
2x screws, T20, 1.5 Nm
Align the clips then press downward to install upper shroud onto lower shroud

참고
4x clips
Install steering wheel to steering column

참고
Align the marking and keyed part of steering wheel and column
Install bolt securing steering wheel to steering column

참고
1x patch bolt, 10mm hex, 80 Nm, Install new patch bolt
Connect steering wheel

참고
1x connector
Position driver air bag assembly

참고
1x connector
Install driver air bag assembly to steering wheel

참고
3x datums, 2x spring clips, Inspect to make sure lower horn bracket is properly secured to steering wheel before installing driver air bag, make sure that the driver air bag harness doesn’t get caught between the driver air bag and the horn mechanism, verify air bag is fully engaged
Install main decor assembly

참고
15x clips, 1x center clip
Install the LH footwell duct into HVAC module

참고
1x push clip
Connect the driver knee air bag and install into vehicle

참고
1x connector, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector
Install fasteners securing driver knee air bag to vehicle

참고
4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 1x push clip, If vehicle equipped with T30 bolts, update to E10
Install connectors to LH footwell cover and position for installation, securing front tabs to driver air bag assembly

참고
3x tabs, 1x Ethernet connector, 1x puddle light connector, APAC specific vehicles have an additional OBDII connector
Install screw and clips securing LH footwell cover

참고
1x screw, T20, 2.5 Nm, 2x push clips
Install RH upper A-pillar trim

참고
3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
Install RH lower A-pillar trim

참고
1x clip, 2 guide tabs, Align 2 front tabs then align slot with harness bracket and then push rear clip to secure to lower B-pillar
Install clip for RH lower A-pillar trim

참고
1x push clip
Install RH mid A-pillar assembly

참고
1x clip, 1x tab, Align bottom tab then push on top clip to fully seat mid A-pillar, Make sure seal seat on top of trim
Install RH air wave bezel cap to main decor assembly

참고
2x clips, Newer vehicles are equipped with solid bezel.
Install RH IP end cap

참고
3x clips
Install LH upper A-pillar trim

참고
3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
Install LH lower A-pillar trim

참고
2x clip, 3 guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, fully seat seal along trim
Install clip for LH lower A-pillar trim

참고
1x push clip
Install LH mid A-pillar assembly

참고
1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
Install LH air wave bezel cap to main decor assembly

참고
2x clips, Newer vehicles are equipped with solid bezel.
Install LH IP end cap

참고
3x clips
Install center console into vehicle

참고
Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place
Connect USB harness at right front of center console

참고
1x USB connector
Connect harness to rear of center console

참고
1x connector
Install RH front exterior bolts to center console

참고
2x bolts, 10mm, 7 Nm
Install RH console side panel carpet

참고
1 tab, 12x clips, Position side panel and align the front tab. Push the console panel from the front towards the rear
Install RH front floor mat
Install LH front exterior bolts to center console

참고
2x bolts, 10mm, 7 Nm
Install LH console side panel carpet

참고
1 tab, 12x clips, Position side panel and align the front tab. Push the console panel from the front towards the rear
Install LH front floor mat
Connect first responder loop

참고
1x connector, Engage locking tab, Connect FRL before connecting 12V to avoid damage to car computer
Connect 12V negative terminal

참고
1x nut, 10mm, 6 Nm
Move RH front seat forward
Install RH rear exterior bolt to center console

참고
1x bolt, 10mm, 7 Nm
Move RH front seat to original position
Move LH front seat forward
Install LH rear exterior bolt to center console

참고
1x bolt, 10mm, 7 Nm
Install console lower rear panel

참고
5x clips
Move LH front seat to original position
Raise and support vehicle

참고
Ensure vehicle is not charging, Remove charging cable if it's plugged in
Re-establish vehicle connection to Toolbox 3.0
Select "Actions/Autodiag" and search for "HVAC Performance"
Select
TEST-SELF_VCRIGHT_X_HVAC-PERFORMANCE
via Toolbox: (link)via Service Mode:
Thermal ➜ Actions ➜ Test HVAC Performance
Thermal ➜ Actions ➜ Test HVAC Performance
, click Run and allow routine to complete
참고
Select ‘X’ at top right of window to close once complete
Remove HSD or RJ45 cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
Connect washer pump and level sensor connectors

참고
2x connectors
Install washer tank into position
Install upper bolt securing washer tank to vehicle

참고
1x bolt, 10mm, 3 Nm
Secure harness clip onto LH side of washer tank inlet

참고
1x clip
Raise vehicle partially and lower lift onto locks

참고
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
Remove LH front wheel

참고
5x nuts, 21mm, 175 Nm
Partially release LH front wheel liner

참고
2x push clips
Install lower bolt securing washer tank to vehicle

참고
1x bolt, 10mm, 3 Nm
Install LH front wheel liner to vehicle

참고
6x clips, 1x bolt, 10mm, 5 Nm, Newer vehicles may be equipped with 2x push clips securing lower portion of liner to body
Install LH front wheel

참고
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
Lower vehicle until tires are touching ground

참고
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Torque LH front wheel

참고
5x nuts, 21mm, 175 Nm
Install LH front wheel center cap

참고
1x cap, Verify emblem is aligned with valve stem
Install wiper module to vehicle
Connect wiper module connector

참고
1x connector, Do NOT place limbs within the linkage movement area as wiper arms will automatically transition to parking mode
Install the bolts securing wiper module

참고
3x bolts, 10mm, 7 Nm
Install fresh air intake assembly

참고
2x studs, Maneuver between cowl and frunk
Install cowl screen assembly

참고
2x push clips, 6x clips
Install RH shock tower cover

참고
2x push clips
Install LH shock tower cover

참고
2x push clips
Install LH wiper arm and hose assembly onto vehicle

참고
Washer hose shall be routed over the arm pivot joint, not under
Install nut securing LH wiper arm to wiper module

참고
1x nut, 15mm, 25 Nm, Make sure wiper tip is aligned between two indicators at windshield
Connect washer hose from LH wiper arm to Y-tube fitting and secure washer hose clips

참고
2x clips, 1x hose
Install LH wiper arm nut cover

참고
1x cover
Install RH wiper arm and hose assembly onto vehicle
Install nut securing RH wiper arm to wiper module

참고
1x nut, 15mm, 25 Nm, Make sure wiper tip is aligned between two indicators at corner of windshield
Connect washer hose from RH wiper arm

참고
2x clips, 1x hose, Connect to Y-tube fitting and secure washer hose clips
Install RH wiper arm nut cover

참고
1x cover
Install frunk assembly to vehicle

참고
12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles. Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam
Install bolts securing frunk assembly

참고
7x bolts, 10mm, 5 Nm, Lower RBN covers after installing upper fasteners, Newer vehicles may not be equipped with covers
Install frunk close out panel

참고
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
Install cabin intake upper duct assembly

참고
3x clips, Some configurations may come with 4x clips
Install rear apron

참고
12x clips
Close hood
Verify operation of windshield washers and wipers
Close all four doors

참고
Unlatch rear doors before closing
Raise all windows
Remove vehicle from lift

참고
Lower rack arms fully and remove from under vehicle