2023-04-14

Check Base - Sun Visor - LH (Remove and Replace)

Correction code 15051052 0.06 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1080559-20-A 공구, 토크 스크루드라이버, 0.8-2.0NM (북미, APAC)
  • 1080559-21-A 공구, 토크 스크루드라이버, 0.8-2.0NM (EMEA)

Torque Specifications

표 1. Torque Specifications: Check Base - Sun Visor - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
선바이저 체크 베이스를 차체에 고정하는 볼트
0.8 Nm (7 lbs-in)
  • Torx T15 소켓
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
Reuse

Remove

  1. 체크 베이스에서 선바이저를 분리합니다.
  2. 차량에 신형 유형의 자석 체크 베이스가 장착되어 있는 경우 플라스틱 트림 공구를 사용하여 체크 베이스를 탈거합니다. 볼트-온 버전의 경우 다음 단계를 진행합니다.
  3. 체크 베이스에 선바이저 체크 커버를 고정하는 클립을 조심스럽게 분리한 후, 차량에서 커버를 탈거합니다.
  4. 선바이저 체크 베이스를 차체에 고정하는 볼트를 탈거한 다음 차량에서 체크 베이스를 탈거합니다.
    0.8 Nm (7 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T15 소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    손상을 방지하려면 장착 중에 이 토크 규격을 따르고 전동 도구를 사용하지 마십시오.

Install

Installation procedure is the reverse of removal.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
손상을 방지하려면 체크 베이스를 세게 잡아 당기거나 비틀지 말고 헤드라이너에 고정되어 있는지 확인합니다.
Informational PurposesAn informational icon, calling your attention
참고
볼트-온 버전의 경우: 장착 시 사용한 패스너의 부품 번호가 1120162-00-B 이상인지 확인합니다. 구형 패스너는 토크 규격이 다릅니다.