2024-06-04

Guide - Probing - HV Battery (Remove and Replace)

Correction code 16303802 1.26 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-06-01: 절차를 완전히 수정하고 신규 장착 절차에 대한 링크를 추가했습니다.
Informational PurposesAn informational icon, calling your attention
참고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Remove

  1. 정비 절차에서 HV 배터리 탐지 가이드를 탈거하도록 요청한 경우 7단계로 이동합니다. 그렇지 않은 경우 다음 단계로 진행합니다.
  2. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  3. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  4. Perform Vehicle HV Disablement Procedure. See Vehicle HV Disablement Procedure.
  5. 보조 베이 커버를 탈거합니다. 참조 항목: Cover - Ancillary Bay (Remove and Replace).
  6. 점화식 배터리 차단기를 탈거합니다. 참조 항목: Pyrotechnic Battery Disconnect (Remove and Replace).
  7. HV 배터리 탐지 커버가 신형인지 확인합니다.
    그림 1. 신형
    그림 2. 구형
  8. HV 배터리 탐지 가이드가 구형인 경우 신형을 장착한 다음 탐지 가이드 탈거를 요청한 정비 절차로 돌아가십시오. 참조 항목: Guide - Probing - HV Battery (Retrofit).
  9. HV 배터리 음극 컨택터 하네스를 옆으로 옮긴 다음 HV 배터리 탐지 가이드를 위로 똑바로 들어 올려 보조 베이에서 탈거합니다.
  10. 정비 절차에서 HV 배터리 탐지 가이드를 탈거하도록 요청한 경우 해당 절차로 돌아갑니다.

Install

  1. HV 배터리 음극 컨택터 하네스를 옆으로 옮기고 HV 배터리 탐지 가이드를 고속 충전 컨택터 버스바 위에 놓은 다음 탐지 가이드를 버스바 위로 내리 누릅니다.
  2. 정비 절차에서 HV 배터리 탐지 가이드를 장착하도록 요청한 경우 해당 절차로 돌아갑니다. 그렇지 않은 경우 다음 단계로 진행합니다.
  3. 점화식 배터리 차단기 고정 지점에서 전압을 측정한 다음 점화식 배터리 차단기를 장착합니다. Pyrotechnic Battery Disconnect (Remove and Replace)을(를) 참조하십시오.
  4. 보조 베이 커버를 장착합니다. 참조 항목: Cover - Ancillary Bay (Remove and Replace).
  5. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).