Motor - Recliner - Backrest - Driver Seat (Remove and Replace)
Correction code
13016602
0.96
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
- 2023-05-03: 전면 동승석 시트 보정 및 OCS 보정을 위한 단계를 추가했습니다.
Remove
- 운전석 등받이에서 허리 지지대 어셈블리를 탈거합니다. 참조 항목: Lumbar Support - Backrest - Driver Seat (Remove and Replace).
-
리클라이너 튜브를 프레임에 고정하는 클립을 탈거하여 폐기합니다.
-
고무 해머를 사용하여 클립이 전에 위치해 있던 리클라이너 튜브를 두드린 다음, 튜브를 프레임에서 탈거합니다.
참고튜브를 탈거하려면 튜브를 시트 밖으로 빼내기 위해 고무 해머로 여러 번 두드릴 필요가 있을 수 있습니다.
-
리클라이너 모터를 시트 등받이 프레임에 고정하는 볼트를 탈거합니다.
-
프레임에서 리클라이너 모터를 탈거합니다.
Install
-
리클라이너 모터를 시트 등받이 프레임에 장착하고, 모터를 프레임에 고정하는 볼트를 손으로 조입니다.
-
리클라이너 튜브를 시트 등받이 프레임에 장착하고, 리클라이너 모터를 통해 프레임의 반대쪽에 장착합니다.
참고고무 해머를 사용하여 리클라이너 튜브를 두드려서 튜브가 시트 등받이 프레임 밖으로 16mm까지 확장되도록 합니다.
-
보조 작업자와 함께 새 클립을 리클라이너 튜브에 장착합니다.
참고12mm 깊이 소켓과 고무 해머를 사용하여 클립을 리클라이너 튜브에 대고 두드립니다. 보조 작업자가 튜브의 반대쪽 끝에서 다른 해머를 사용하여 마주 보고 두드리게 합니다.
-
리클라이너 모터를 시트 등받이 프레임에 고정하는 볼트를 조입니다.5 Nm (3.7 lbs-ft)
- 허리 지지대 어셈블리를 운전석 등받이에 장착합니다. 참조 항목: Lumbar Support - Backrest - Driver Seat (Remove and Replace).
-
If servicing the front passenger seat in
a North American vehicle:
- Remove all objects from the front passenger seat before beginning calibration.
- On the vehicle touchscreen, touch Software Reinstall - Touchscreen. If the vehicle firmware is not 2023.2.11 or newer, update the vehicle firmware. See Software Update. and check the vehicle firmware version. If the vehicle firmware is 2023.2.11 or newer, perform a software reinstall. See
- Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
- Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
- In Toolbox, click on the Actions tab, and then search for "OCS".
- Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration routine.
- Click on the Actions tab, and then search for "Seat calibration".
- Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate routine.
- Disconnect Toolbox and remove the laptop from the vehicle.
-
Calibrate the driver seat: