2024-04-16

Sensor - Ride Height - Rear - LH (Remove and Replace)

Correction code 31036102 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. 토크 규격: Sensor - Ride Height - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 후면 지상고 센서를 LH 후면 상단 후방 링크에 고정하는 너트
10 Nm (7.4 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 래칫/토크 렌치
Reuse
LH 후면 지상고 센서를 후면 서브프레임에 고정하는 너트
10 Nm (7.4 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 래칫/토크 렌치
Reuse

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. LH 후면 휠을 탈거합니다. 참조 항목: Wheel (Remove and Replace).
  3. LH 후면 지상고 센서를 LH 후면 상단 후방 링크에 고정하는 너트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 래칫/토크 렌치
  4. LH 후면 지상고 센서를 후면 서브프레임에 고정하는 너트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 래칫/토크 렌치
  5. LH 후면 지상고 센서에서 전기 커넥터를 연결 해제한 다음, 차량에서 센서를 탈거합니다.

Install

  1. 전기 커넥터를 LH 후면 지상고 센서에 연결합니다.
  2. LH 후면 지상고 센서를 후면 서브프레임에 고정하는 너트를 장착합니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 래칫/토크 렌치
  3. LH 후면 지상고 센서를 LH 후면 상단 후방 링크에 고정하는 너트를 장착합니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 래칫/토크 렌치
  4. LH 후면 휠을 장착합니다. 참조 항목: Wheel (Remove and Replace).
  5. 리프트에서 차량을 내립니다.