2024-12-17

Motor - Seat Tilt - Driver Seat (Remove and Replace)

Correction code 13011502 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.
  • 2024-12-09: 미니 틸트 모터 구성 정보를 추가했습니다.
  • 2023-05-23: 전면 동승석 시트에 대한 참고 사항 및 추가 단계를 추가했습니다.
  • 2023-05-03: 전면 동승석 시트 보정 및 OCS 보정을 위한 단계를 추가했습니다.

Remove

  1. 운전석 시트를 탈거합니다. 참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).
  2. 운전석 시트 외측 사이드 실드를 탈거합니다. 참조 항목: Side Shield - Outboard - Driver Seat (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    참고
    전면 동승석 시트에 대해 이 절차를 수행하는 경우 이 단계는 필요하지 않습니다.
  3. 운전석 시트 틸트 모터 커넥터에서 전기 하네스를 연결 해제합니다.
  4. 전면 동승석 시트에 대해 이 절차를 수행하는 경우: RH 전면 시트 안전벨트 버클 하네스를 시트 쿠션 프레임에 고정하는 클립(2개)을 풉니다.
  5. 운전석 시트 틸트 모터를 시트 프레임에 고정하는 볼트를 탈거합니다.
  6. 운전석 시트 틸트 모터 조정 암을 시트 쿠션 틸트 튜브 브래킷에 고정하는 볼트를 탈거한 다음 시트 프레임에서 운전석 시트 틸트 모터를 탈거합니다.

Install

  1. 운전석 시트 틸트 모터를 시트 프레임에 장착한 다음 시트 쿠션 틸트 튜브 브래킷에 운전석 시트 틸트 모터 조정 암을 고정하는 볼트를 장착합니다.
    16 Nm (11.8 lbs-ft)
  2. 운전석 시트 틸트 모터를 시트 프레임에 고정하는 볼트(3개)를 장착합니다.
    7.5 Nm (5.5 lbs-ft)
  3. 탈거한 경우, RH 전면 시트 안전벨트 버클 하네스를 시트 쿠션 프레임에 고정하는 클립(2개)을 장착합니다.
  4. 운전석 시트 틸트 모터 커넥터에 전기 하네스를 연결합니다.
  5. 탈거한 경우, 운전석 시트 외측 사이드 실드를 장착합니다. 참조 항목: Side Shield - Outboard - Driver Seat (Remove and Replace).
  6. 운전석 시트를 장착합니다. 참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).
  7. 2024년 6월 이후 조달된 교체용 전면 시트 어셈블리와 시트 쿠션 프레임 어셈블리에는 새롭게 설계된 Tesla "미니 틸트" 모터가 장착되어 있으며, 이러한 부품(또는 틸트 모터 자체)을 교체하려면 구성을 변경해야 할 수 있습니다. 표의 구성 정보를 검토하고 구성 업데이트가 필요한 경우 다음 하위 단계를 수행합니다.
    1. Infotainment DashboardVehicle Configuration 섹션에 액세스합니다. 참조 항목: 게이트웨이 구성(표시 및 변경).
    2. 표에 설명된 틸트 모터의 조합에 따라 cfg_frontSeattype을 업데이트합니다.
  8. If servicing the front passenger seat in a North American vehicle:
    1. Remove all objects from the front passenger seat before beginning calibration.
    2. On the vehicle touchscreen, touch Controls (Vehicle Icon) > Software and check the vehicle firmware version. If the vehicle firmware is 2023.2.11 or newer, perform a software reinstall. See Software Reinstall - Touchscreen. If the vehicle firmware is not 2023.2.11 or newer, update the vehicle firmware. See Software Update.
    3. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
    4. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
    5. In Toolbox, click on the Actions tab, and then search for "OCS".
    6. Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration routine.
    7. Click on the Actions tab, and then search for "Seat calibration".
    8. Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate routine.
    9. Disconnect Toolbox and remove the laptop from the vehicle.
  9. Calibrate the driver seat:
    1. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
    2. In Toolbox, click on the Actions/Autodiag tab, and then search for "Calibration".
    3. Click Left Seat Calibration, click Run, and allow the routine to complete.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      경고
      Make sure that nothing is on the seat during the calibration routine.
    4. Disconnect Toolbox and remove the laptop from the vehicle.