2023-08-31

Switch - Interior Door Release - Rear - LH (Remove and Replace)

Correction code 15131802 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

    Remove

    1. LH 후면 도어를 열고 LH 후면 창문을 내립니다.
    2. LH 후면 도어 퍼들 라이트를 탈거합니다. Puddle Light - Rear Door - LH (Remove and Replace)을(를) 참조하세요.
    3. LH 후면 도어 트림 패널을 탈거합니다. Panel - Door Trim - Rear - LH (Remove and Install)을(를) 참조하세요.
    4. (3개)을 분리한 다음 LH 후면 도어 트림 패널에서 NVH 패드를 탈거합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      보조 작업자가 도어 트림을 잡고 있는 것이 좋습니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      도어 전기 커넥터 및 클립을 탈거하지 마십시오.
    5. 도어 트림 패널을 부드럽게 들어 올려 실내 도어 해제 핸들 스위치를 도어 트림 패널에 고정하는 볼트를 탈거합니다.
      6 Nm (4.4 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      참고
      Use of the following tool(s) is recommended:
      • Torx T20 소켓
      Warning IconA warning icon, calling your attention to a possibly risky situation
      경고
      Pry carefully and do not damage the plastic rivets. Damage to the rivets could compromise the integrity of the door trim panel.
    6. 전기 커넥터에서 핀(3개)을 분리합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      핀 및 플러그를 분리하여 좁은 트림 패널 공간을 통과할 수 있도록 합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      핀 및 전기 커넥터의 위치를 표시합니다.
    7. 작업 영역 주변에 마스킹 테이프를 부착하여 도어 트림 패널을 보호합니다.
    8. 실내 도어 핸들의 전면부를 들어 올립니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      실내 도어 해제 스위치를 탈거할 공간이 충분한지 확인하십시오.
    9. 탭(2개)을 분리한 다음 도어 트림 패널에서 실내 도어 해제 스위치를 탈거합니다.

    Install

    1. 새 실내 도어 해제 스위치의 전기 커넥터에서 핀(3개)을 분리합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      핀 및 플러그를 분리하여 좁은 트림 패널 공간을 통과할 수 있도록 합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      핀 및 전기 커넥터의 위치를 표시합니다.
    2. 실내 도어 해제 스위치를 도어 트림 패널에 고정하는 탭(2개)을 조입니다.
    3. 핀을 전기 커넥터에 고정합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      핀 및 전기 커넥터의 위치를 표시합니다.
    4. 실내 도어 핸들의 전면부를 도어 트림 패널에 고정합니다.
    5. 도어 트림 패널에서 마스킹 테이프를 제거합니다.
    6. 도어 트림 패널을 부드럽게 들어 올려 실내 도어 해제 핸들을 도어 트림 패널에 고정하는 볼트를 장착합니다.
      6 Nm (4.4 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      Use of the following tool(s) is recommended:
      • Torx T20 소켓
      Warning IconA warning icon, calling your attention to a possibly risky situation
      경고
      Pry carefully and do not damage the plastic rivets. Damage to the rivets could compromise the integrity of the door trim panel.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      경고
      Replace the door trim panel if the plastic rivets are damaged during service.
    7. NVH 패드를 후면 도어 트림 패널에 장착하고 탭(3개)으로 패드를 고정합니다.
    8. LH 후면 도어 퍼들 램프를 장착합니다. Puddle Light - Rear Door - LH (Remove and Replace)을(를) 참조하세요.
    9. LH 후면 도어 트림 패널을 장착합니다. Panel - Door Trim - Rear - LH (Remove and Install)을(를) 참조하세요.