2024-06-25

Tie Rod End - LH (Remove and Replace)

Correction code 32010302 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Tie Rod End - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
타이로드를 너클에 고정하는 너트
180 Nm (132.7 lbs-ft)
  • 22mm 소켓
  • 14mm 12pt 콤비네이션 렌치
Replace 1109263-00-B
LH 타이로드 엔드의 잼 너트
80 Nm (59.0 lbs-ft)
  • 21mm 12pt 콤비네이션 렌치
Reuse

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. LH 전면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  3. 나중에 LH 타이로드 엔드 장착 중 둘을 다시 정렬할 수 있도록 페인트 펜을 사용하여 타이로드 및 잼 너트에 확인 표시를 적용합니다.
  4. LH 타이로드 엔드의 잼 너트를 풉니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 21mm 12pt 콤비네이션 렌치
  5. 타이로드를 너클에 고정하는 너트를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 22mm 소켓
    • 14mm 12pt 콤비네이션 렌치
  6. 고무 망치를 사용하여 너클에서 LH 타이로드 엔드를 탈거합니다.
  7. 타이로드를 시계 반대 방향으로 회전하여 스티어링 연결부에서 타이로드를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스티어링 연결부에서 타이로드를 분리하기 위해 회전한 수를 기록합니다.

Install

  1. 타이로드 엔드를 탈거 도중 기록했던 회전 수와 정확히 일치하게 시계 방향으로 돌려 스티어링 연결부에 장착합니다.
  2. 타이로드 엔드를 너클에 고정하는 새 너트를 장착합니다.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 22mm 소켓
    • 14mm 12pt 콤비네이션 렌치
  3. 확인 표시를 사용하여 타이로드를 잼 너트에 정렬하고 너트를 조여 타이로드 엔드를 제자리에 고정합니다.
    80 Nm (59.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 21mm 12pt 콤비네이션 렌치
  4. LH 전면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  5. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See 얼라인먼트 요구 사항 - 서스펜션.