11/02/2024 07:30:14

브레이크 캘리퍼 - 후면 - 한 쌍(탈거 및 교체)

33010522 0.78 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
브레이크 오일은 페인트를 녹입니다. 도장면에 유출된 브레이크 오일을 닦을 수 있도록 깨끗한 수건과 다량의 물을 준비해 두십시오.
Informational PurposesAn informational icon, calling your attention
참고
사용한 브레이크 오일은 현지 환경 규정에 따라 폐기합니다.
Informational PurposesAn informational icon, calling your attention
참고
This procedure is applicable to both base and sport type brake calipers.
  1. Prepare the vehicle for lifting, but do not lift it at this time. See 차량 올리기 - 2 포스트 리프트.
  2. Open the LH front door and lower the window.
  3. Enable Service Model via the touchscreen. See 정비 모드.
  4. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
  5. Put the EPB in Service Mode: on the touchscreen, touch Chassis > Brakes > EPB Service Mode, from the drop down menus, select Both and Start, and then touch Run.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The vehicle may roll freely.
  6. Remove LH and RH rear wheels. See 휠 어셈블리(탈거 및 장착).
  7. Disconnect the LH rear brake caliper connector.
  8. Remove the bolt that attaches the LH rear brake caliper harness bracket.
  9. Position an oil drain container under LH rear brake hose area.
  10. Remove the tube nut that attaches the LH rear brake line to the LH rear brake hose.
  11. Remove and discard the LH rear jounce hose clip.
  12. Position the oil drain container under the LH rear brake caliper area.
  13. Remove the bolt that attaches the LH rear brake hose to the LH rear brake caliper.
  14. Remove and discard the bolts (x2) that attach the LH rear brake caliper bracket to the knuckle, and then remove the brake caliper from the vehicle.
  15. Install new bolts (x2) that attach the LH rear brake caliper bracket onto the knuckle (torque 83 Nm).
    Informational PurposesAn informational icon, calling your attention
    참고
    Mark the bolts with a paint pen after torquing.
  16. Install a new bolt and new copper washers (x2) that attach the LH rear brake hose to the LH rear brake caliper (torque 42 Nm).
    Informational PurposesAn informational icon, calling your attention
    참고
    Mark the bolt with a paint pen after torquing.
  17. Install a new LH rear jounce hose clip to attach the hose to the body.
  18. Position the oil drain container under the LH rear brake hose area.
  19. Install the LH rear brake line tube nut to the LH rear brake hose (torque 16 Nm).
  20. Install the nut that attaches the LH rear brake caliper harness bracket (torque 5 Nm).
  21. Connect the LH rear brake caliper connector.
  22. Repeat steps 7 through 21 on the RH side of the vehicle.
  23. Bleed the LH and RH brake calipers. See 브레이크 오일 블리딩 - 캘리퍼 1개.
  24. Put the vehicle into park.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that parking brakes are engaged. Putting the vehicle into Park also disables EPB Service Mode.
  25. Perform a road test and burnish the brakes. See 브레이크 패드 - 버니싱.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure proper brake pedal feel and performance. Add correction code 33013000 as a separate activity to the SV.