2024-10-07

Receiver Dryer and Desiccant (Non-Heat Pump) (Remove and Replace)

Correction code 18202002 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-09-20: 냉매 회수/재충전 교정 코드 18200102를 서비스 방문에 별도 활동으로 추가하는 참고 사항을 추가했습니다.
  • 2024-09-10: 에어컨 시스템을 대상으로 작업 수행 시 안면 보호, 내열 장갑, 고무 부츠 및 에이프런 또는 전신 방수복 등 적합한 보호용 의류를 착용해야 한다는 경고를 추가했습니다.
  • 2024-06-12: 슈레더 밸브에 대한 주의 사항을 추가했습니다.
  • 2024-04-02: 어큐뮬레이터를 열기 전에 A/C 시스템의 압력을 확인하라는 알림을 추가했습니다.
  • 1145232-00-A 흡습 필터 탈거 공구
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
HFO-R1234yf and R134a are considered hazardous and, if handled incorrectly, can cause serious injury. Suitable personal protective equipment, consisting of face and eye protection, safety glasses, face shield, heat-proof gloves, chemical resistant gloves, rubber boots and apron or waterproof overall must be worn when carrying out operations on the air conditioning system.
Informational PurposesAn informational icon, calling your attention
참고
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Remove

  1. A/C 냉매 회수를 수행합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Make sure there is no overpressure in the A/C system before performing the following steps. Failure to do so may result in damage to components and/or personal injury.
  2. 차량에서 AC 호스를 탈거합니다.
  3. 슈레더 밸브(2개)를 조심스럽게 눌러 A/C 라인에서 진공을 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    슈레더 밸브를 모두 눌러야 합니다. 그렇지 않을 경우 상해를 입을 수도 있습니다.
  4. 후드 내 보강재 브래킷을 차체에 고정하는 볼트(2개)를 탈거한 다음 냉각 팬 모듈에서 브래킷을 탈거합니다.
  5. 콘덴서 LH에서 캡을 탈거합니다.
  6. 스냅 링을 탈거하기 위해 11mm 소켓을 사용하여 콘덴서의 내측 캡을 살짝 누릅니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Wear the Face Shield throughout the entire process to protect against foreign objects flying out under pressure.
  7. 스냅 링을 콘덴서에서 탈거합니다.
  8. M8x1.25mm 볼트를 내측 캡에 나사산 천공하고 볼트를 사용하여 내측 캡을 당겨 뺍니다.
  9. 콘덴서에서 제습제 백을 탈거합니다.
  10. 흡습 필터 탈거 공구와 슬라이드 해머를 사용하여 흡습 필터 스크린을 탈거합니다.

Install

  1. 3/8인치 익스텐션을 사용하여 새 흡습 필터를 콘덴서에 눌러 넣습니다. 해머로 가볍게 탭하여 필터를 완전히 안착합니다.
  2. 새 제습제 백을 콘덴서에 삽입합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Wear the Face Shield throughout the entire process to protect against foreign objects flying out under pressure.
  3. 내측 캡을 콘덴서에 장착하고 스냅 링을 위해 바로 아래 홈을 누릅니다.
  4. 내측 캡에서 볼트를 탈거합니다.
  5. 스냅 링을 콘덴서에 장착하고 스냅 링이 홈에 완전히 안착했는지 확인합니다.
  6. 캡을 장착합니다.
    4 Nm (2.9 lbs-ft)
  7. 후드 내 보강재 브래킷을 냉각 팬 모듈에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    트레일링 탭이 아이솔레이터 고무에 접촉하고 위에서 봤을 때 챔퍼 처리된 가장자리가 명확히 보이도록 냉각 팬 모듈 탭을 아이솔레이터에 삽입해야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각 팬 모듈 마운트의 트레일링 에지가 아이솔레이터의 하단 터널에 닿아야 합니다.
  8. 후드 내 보강재 브래킷을 차체에 고정하는 볼트(2개)를 장착합니다.
    16 Nm (11.8 lbs-ft)
  9. LH 냉각 팬 모듈 아이솔레이터를 위해 볼트(2개)를 풉니다.
  10. 아이솔레이터를 전방으로 미는 동안 볼트(2개)를 조입니다.
    6 Nm (4.4 lbs-ft)
  11. RH 냉각 팬 모듈 아이솔레이터에서 9 단계 및 10 단계를 반복합니다.
  12. A/C 냉매 재충전을 수행합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).