2025-06-27

Bushing – Front Drive Unit – RH (Remove and Replace)

Correction code 39011102 2.94 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 차량에서 전면 서브프레임 어셈블리를 탈거합니다. 참조 항목: Subframe Assembly - Front (Dual Motor) (Remove and Install).
  2. 부싱 공구를 RH 전륜 구동 장치 부싱에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    특수 도구를 조립할 때 표시된 대로 "K", "B" 및 "I" 컵을 사용합니다.
    그림 1. 명확한 이해를 위해 다른 어셈블리를 표시하지 않음
  3. 반대쪽 너트를 제자리에 고정하고 있는 동안 렌치로 베어링 쪽 부싱 공구 너트를 돌립니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    베어링 쪽 부싱 공구 너트에만 토크를 가하십시오.
    그림 2. 빨간색으로 강조 표시한 너트에만 토크 가함
  4. 부싱이 전륜 구동 장치에서 밀려 나오면 부싱 공구를 분리한 다음 부싱을 탈거합니다.

Install

  1. 부싱 공구를 설정하여 새 부싱을 압입합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    특수 도구를 조립할 때 표시된 대로 "L", "J" 및 "C" 컵을 사용합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    "J" 컵 상부에 고무 탭이 보이는지 확인합니다.
    그림 3. 부싱 장착 시 "L", "J" 및 "C" 컵 사용됨
    그림 4. "J" 컵 상부에 고무 탭이 보임
  2. 부싱 플랜지가 전륜 구동 장치와 접촉할 때까지 렌치로 베어링 면 부싱 공구 너트를 돌립니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    베어링 쪽 부싱 공구 너트에만 토크를 가하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    부싱을 장착하는 동안 "J" 컵 상부에 고무 탭이 보이는지 확인합니다.
    그림 5. 빨간색으로 강조 표시한 너트에만 토크 가함
  3. 부싱 공구를 분리한 후 구동장치에서 부싱 공구를 탈거합니다.
  4. 부싱 정렬 러그가 12시 방향을 향하는지 확인합니다.
    그림 6. 명확한 이해를 위해 다른 어셈블리를 표시하지 않음
  5. 전면 서브프레임 어셈블리를 차량에 장착합니다. 참조 항목: Subframe Assembly - Front (Dual Motor) (Remove and Install).