2024-10-23

Motor - Brake Caliper - Rear - LH (Remove and Replace)

Correction code 33052302 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-10-09: 장착 후 도로 테스트를 삭제했습니다.
  • 2024-05-28: EPB 정비 모드 참조를 업데이트했습니다.

Torque Specifications

표 1. 토크 규격: Motor - Brake Caliper - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 후면 EPB 하네스 브래킷을 LH 후면 캘리퍼에 고정하는 볼트
5 Nm (3.7 lbs-ft)
  • 10mm 소켓
Reuse
LH 후면 브레이크 캘리퍼 모터를 브레이크 캘리퍼에 고정하는 볼트(2개)
10.8 Nm (8.0 lbs-ft)
  • 5mm 육각
Reuse

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. LH 후면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  4. 잠금 탭을 분리한 다음 LH 후면 EPB 캘리퍼 커넥터를 연결 해제합니다.
  5. LH 후면 EPB 하네스 브래킷을 LH 후면 캘리퍼에 고정하는 볼트를 탈거합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  6. LH 후면 브레이크 캘리퍼 모터를 차량에 고정하는 볼트(2개)를 탈거한 다음 차량에서 캘리퍼 모터를 탈거합니다.
    10.8 Nm (8.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 5mm 육각

Install

  1. LH 후면 브레이크 캘리퍼 모터를 차량에 배치한 다음 캘리퍼 모터를 차량에 고정하는 볼트(2개)를 장착합니다.
    10.8 Nm (8.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 5mm 육각
  2. LH 후면 EPB 하네스 브래킷을 LH 후면 캘리퍼에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
  3. LH 후면 EPB 캘리퍼 커넥터를 연결한 다음 잠금 탭을 체결합니다.
  4. 주차 버튼을 길게 눌러 EPB 정비 모드를 해제합니다.
  5. LH 후면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  6. 리프트에서 차량을 내립니다. 참조 항목: Raise Vehicle - 2 Post Lift.