2024-08-16

Vehicle Sanitation - Evaporator - Tunap 994 (EMEA)

Correction code 18106728 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-08-08: 기존 절차에서 Tunap 996 및 Tunap I5880을 사용하는 절차를 제거했습니다.
  • 1769621-00-A 포밍 클리너, TUNAP 994, AC 증발기
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
사용하지 않을 때는 세척 제품을 가연성 물질용으로 설계된 캐비닛에 보관하십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
모든 전기 부품(커넥터, 하네스, 차체 컨트롤러 등)에 과도하게 분사되지 않도록 보호하십시오.
Informational PurposesAn informational icon, calling your attention
참고
사용한 세척제와 용기는 모든 지자체, 지역, 국가 및 국제 규정에 따라 폐기하십시오.

절차

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차를 시작하기 전에 증발기 세척 제품과 함께 제공된 안전 정보를 읽으십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
증발기 세척 제품을 사용할 때는 보안경과 니트릴 내화학성 장갑을 착용하고 환기가 잘되는 곳에서 작업하십시오.
  1. A/C를 끄고 실내 공기를 HI 온도, 블로워 속도 최대 및 외기 유입으로 설정한 다음 블로워를 8분간 작동합니다.
  2. 실내 필터를 탈거합니다. 참조 항목: Filter - Cabin (Remove and Replace).
  3. 터치스크린에서 차량 전원을 끕니다.
  4. 냉각수 배출 용기 또는 흡수재를 차량 전면 아래에 놓습니다.
  5. 압력 컵 스프레이 건의 탱크에 Tunap 994 위생 세척제 1리터를 부은 다음 정비소 공기 공급장치를 스프레이 건에 연결합니다.
  6. 프로브를 HVAC 필터 하우징에 삽입한 다음 세척 용액을 증발기에 모두 분사합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    프로브의 분사구가 차량 후면 쪽으로 증발기를 향해야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    증발기 전체를 세척 용액으로 코팅하십시오.
  7. 세척 용액이 증발기에 안착하도록 30분간 기다립니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기다리는 동안 차량 아래를 점검하고, 필요 시 냉각수 배출 용기/흡수재를 조정합니다.
  8. 세척 용액이 충분히 오래 안착했으면 새 실내 필터를 장착합니다. 참조 항목: Filter - Cabin (Remove and Replace).
  9. A/C를 켜고 실내 공기를 LO 온도, 블로워 속도 최대 및 외기 유입으로 설정합니다.
  10. 세척 폼이 HVAC 배출구를 통해 나옵니다. HVAC 배출구에서 깨끗한 물이 나오면 다음 단계로 진행합니다.
  11. 차량 아래에서 냉각수 배출 용기/흡수재를 제거합니다.