2025-09-11

IP Carrier (Remove and Install)

Correction code 140521011.92 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-08-08: 운전석 및 전면 동승석 시트 탈거 단계를 삭제했습니다.

Torque Specifications

표 1. Torque Specifications: IP Carrier (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
전면 동승석 에어백-크로스 카 빔 볼트
8 Nm (5.9 lbs-ft)
  • 외부 Torx E10 또는 Torx T30 소켓
  • 4인치 익스텐션
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
Replace
IP 캐리어-크로스 카 빔 나사
2.3 Nm (1.7 lbs-ft)
  • Torx T20 소켓
  • 4인치 익스텐션
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
Reuse

Remove

  1. 모든 도어를 열고 창문을 모두 내립니다.
  2. 센터 콘솔을 탈거합니다. 참조 항목: Center Console (Remove and Install)
  3. LH 및 RH 하단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  4. LH 및 RH 상단 A필러 트림을 탈거합니다. 참조 항목: Trim - A-Pillar - Upper - LH (Remove and Replace).
  5. LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 터치스크린을 탈거합니다. 참조 항목: Touchscreen (Remove and Replace).
  7. 동승석 발밑 공간 덕트를 탈거합니다. 참조 항목: Duct - Footwell - RH (LHD) (Remove and Replace).
  8. RH 에어 웨이브 덕트를 탈거합니다. 참조 항목: Duct - Air Wave - RH (LHD) (Remove and Replace).
  9. 운전석 발밑 공간 덕트를 탈거합니다. 참조 항목: Duct - Footwell - LH (LHD) (Remove and Replace).
  10. 스티어링 컬럼 제어 모듈(SCCM)을 탈거합니다. 참조 항목: Module - Steering Column Control (Remove and Replace).
  11. LH 전면 통풍구를 탈거합니다. 참조 항목: Vent - Front - LH (Remove and Replace).
  12. RH 전면 송풍구를 탈거합니다. 참조 항목: Vent - Front - RH (Remove and Replace).
  13. LH 및 RH 대시보드 스피커를 탈거합니다. 참조 항목: Speaker - Dash - LH (Remove and Replace).
  14. 중앙 대시보드 스피커를 탈거합니다. 참조 항목: Speaker - Dash - Center (Remove and Replace).
  15. 장착된 경우, 대시보드 트위터를 탈거합니다. 참조 항목: Tweeter - Dash (Remove and Replace).
  16. 전면 동승석 에어백 커넥터(x3)에서 전기 배선 하네스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    북미 이외의 지역 차량에는 커넥터가 2개만 있습니다.
  17. 전면 동승석 에어백을 크로스 카 빔에 고정하는 볼트(4개)를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E10 또는 Torx T30 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  18. 계기판 캐리어를 전면 동승석 에어백의 크로스 카 빔에 고정하는 나사(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  19. 계기판 캐리어를 크로스 카 빔에 고정하는 나사(11개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  20. 터치스크린용 전기 배선 하네스를 계기판 캐리어를 통과시켜 옮깁니다.
  21. 크로스 카 빔에서 계기판 캐리어를 탈거한 다음, 차량에서 계기판 캐리어를 탈거합니다.

Install

  1. 보조 작업자와 함께 계기판 캐리어를 크로스 카 빔에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    계기판 캐리어의 마운팅 탭을 차량의 브래킷에 밀어 넣습니다. HVAC 어셈블리의 상단 중앙에 클립으로 고정된 하네스를 주의하여 분리합니다.
  2. 계기판 캐리어를 크로스 카 빔에 고정하는 나사(11개)를 장착합니다.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  3. 계기판 캐리어를 전면 동승석 에어백의 크로스 카 빔에 고정하는 나사(2개)를 장착합니다.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  4. 전면 동승석 에어백을 크로스 카 빔에 고정하는 볼트(4개)를 장착합니다.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E10 또는 Torx T30 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  5. 전면 동승석 에어백 커넥터(3개)에 전기 배선 하네스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    북미 이외의 지역 차량에는 커넥터가 2개만 있습니다.
  6. LH 및 RH 대시보드 스피커를 장착합니다. 참조 항목: Speaker - Dash - LH (Remove and Replace).
  7. 장착된 경우, 대시보드 트위터를 장착합니다. 참조 항목: Tweeter - Dash (Remove and Replace).
  8. 중앙 대시보드 스피커를 장착합니다. 참조 항목: Speaker - Dash - Center (Remove and Replace).
  9. RH 전면 통풍구를 장착합니다. 참조 항목: Vent - Front - RH (Remove and Replace).
  10. LH 전면 통풍구를 장착합니다. 참조 항목: Vent - Front - LH (Remove and Replace).
  11. 스티어링 컬럼 제어 모듈(SCCM)을 장착합니다. 참조 항목: Module - Steering Column Control (Remove and Replace).
  12. 운전석 발밑 공간 덕트를 장착합니다. 참조 항목: Duct - Footwell - LH (LHD) (Remove and Replace).
  13. RH 에어웨이브 덕트를 장착합니다. 참조 항목: Duct - Air Wave - RH (LHD) (Remove and Replace).
  14. 동승석 발밑 공간 덕트를 장착합니다. 참조 항목: Duct - Footwell - RH (LHD) (Remove and Replace).
  15. 터치스크린을 장착합니다. 참조 항목: Touchscreen (Remove and Replace).
  16. LH 및 RH 상단 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Upper - LH (Remove and Replace).
  17. LH 및 RH 하단 A필러 트림을 장착합니다. 참조 항목: Trim - A-Pillar - Lower - LH (Remove and Replace).
  18. LV 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  19. 센터 콘솔을 장착합니다. 참조 항목: Center Console (Remove and Install)