2026-07-02

Basic Vehicle Inspection (Inspection)

교정 코드 00030700 FRT 0.90 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

경고

이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

참고
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check all windows from the master switch

참고
Document any abnormal operation/noises
Function check LH rear door (exterior)

참고
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH rear door (exterior)

참고
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH front door (exterior)

참고
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check the exterior lights

참고
Recommend assistance, inspect and note functionality of Headlight (LH and RH), Side Repeater (LH and RH), Taillight (LH and RH), CHMSL, Fog Light (LH and RH), Reverse Light (LH and RH), Front Turn Signal (LH and RH), Rear Turn Signal (LH and RH)
Verify operation of windshield wipers and nozzles

참고
Ensure hood and doors are closed prior to activating wipers, Inspect and note functionality for wipers and wiper jets, Check for full range of motion, speed of motion, interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions
Verify operation of horn

참고
Press button on steering wheel and verify high and low tones both sound
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

참고
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

참고
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction
Open hood

참고
Press "Open" button on touchscreen to release latch, Lift lid manually
Remove rear apron

참고
12x clips, Only store rear apron visible face upwards
Remove cabin intake upper duct assembly

참고
3x clips, Some configurations may come with 4x clips
Remove closeout panel from frunk assembly

참고
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Grab closeout panel from bottom then pull it upward to release clips, Disconnect switch
Remove bolts securing frunk assembly

참고
7x bolts, 10mm, 5 Nm
Remove frunk assembly from vehicle

참고
12x clips, Replace any clips if broken or missing, Number of clips may vary on older vehicles
Perform inspection of under hood area

참고
Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Visually inspect brake fluid level
Fill washer reservoir with fluid
Inspect coolant level and top off as necessary

참고
Ensure that fluid level is at Max line
Raise and support vehicle

참고
remove charging equipment
Raise vehicle fully and lower lift onto locks

참고
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove outer fasteners securing front aero shield

참고
9x bolts, 10mm, 5 Nm
Remove front aero shield

참고
2x nuts, 15mm, 8 Nm
Remove rear aero shield

참고
13x bolts, 10mm, 5 Nm
Remove LH rear suspension cover

참고
1x bolt, 10mm, 6 Nm, 2x tabs
Remove RH rear suspension cover

참고
1x bolt, 10mm, 6 Nm, 2x tabs
Check all four tire pressures manually

참고
4x tires, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures
Record tread depth for LH front tire

참고
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for LH rear tire

참고
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for RH rear tire

참고
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for RH front tire

참고
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Inspect underside of vehicle for fluid leaks
Perform inspection of steering components

참고
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of front suspension components

참고
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

참고
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform visual inspection of HV battery enclosure

참고
Check for any dents, scrapes, or other damage
Perform visual inspection of LH front brake pads

참고
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record LH front brake pad thickness

참고
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH front brake rotor condition

참고
Check for excessive rust or wear, Minimum spec: See technical data
Perform visual inspection of LH rear brake pads

참고
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record LH rear brake pad thickness

참고
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH rear brake rotor condition

참고
Check for excessive rust or wear, Minimum spec: See technical data
Perform visual inspection of RH rear brake pads

참고
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record RH rear brake pad thickness

참고
Recommend replacement if 2 mm or less, Check both inboard and outboard pads
Inspect RH rear brake rotor condition

참고
Check for excessive rust or wear, Minimum spec : See technical data
Perform visual inspection of RH front brake pads

참고
Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
Measure and record RH front brake pad thickness

참고
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect RH front brake rotor condition

참고
Check for excessive rust or wear, Minimum spec: See technical data
Install RH rear suspension cover

참고
1x bolt, 10mm, 6 Nm, 2x tabs
Install LH rear suspension cover

참고
1x bolt, 10mm, 6 Nm, 2x tabs
Install rear aero shield

참고
13x bolts, 10mm, 5 Nm, Apply Loctite 222 to bolts before installing
Position front aero shield to vehicle

참고
2x nuts, 15mm, 8 Nm, Hand-tighten the nuts to temporarily hold the panel in place
Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield

참고
9x bolts, 10mm, 5 Nm
Lower vehicle fully

참고
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Remove vehicle from lift

참고
Lower rack arms fully and remove from under vehicle
Install frunk assembly to vehicle

참고
12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles, Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam, replace any damaged clips
Install bolts securing frunk assembly

참고
7x bolts, 10mm, 5 Nm
Install frunk close out panel

참고
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
Install cabin intake upper duct assembly

참고
3x clips, Some configurations may come with 4x clips
Install rear apron

참고
12x clips
Close hood