2026-03-06

Tie Rod Kit - LH (Remove and Replace)

교정 코드 32013202 FRT 0.48 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-12-16: Released new procedure.

탈거

  1. Raise and support the vehicle. See 차량 올리기 - 2 포스트 리프트
  2. Open LH front door
  3. Lower LH front window
  4. Remove the LH front wheel arch liner. See 휠 아치 라이너 - 후면 - LH(탈거 및 교체)
  5. Remove and discard the nut that secures the LH front tie rod end to the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  6. Remove the LH front tie rod end from the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Move the rotor back and forth for easier removal.
  7. Remove and discard the large clamp from the bellows.
  8. Remove the seal clip from the bellows.
  9. Slide the bellows toward the LH outer tie rod end to access the ball joint.
  10. Remove the LH tie rod assembly from the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)

장착

  1. Turn the jam nut on the new tie rod to adjust the length and match the old tie rod before installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Count the threads on the removed tie rod, then adjust to the same count on the new one. This will make alignment adjustment easier.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 21 mm 12pt combination wrench
    • 14 mm 12pt combination wrench
    • Extension
  2. Install the LH inner tie rod assembly onto the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)
  3. Slide the bellows into the clamping position.
  4. Secure the large bellows clamp onto the bellows.
  5. Secure the bellows seal clip onto the bellows.
  6. Position the LH front tie rod end to the LH front knuckle.
  7. Install a new nyloc nut to secure the LH tie rod end to the LH front knuckle
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  8. Remove the LH front wheel arch liner. See 휠 아치 라이너 - 후면 - LH(탈거 및 교체)
  9. Remove the vehicle from the lift. See 차량 올리기 - 2 포스트 리프트
  10. Raise the windows and close the doors.
  11. Review the wheel alignment requirements and add correction code as needed. See 얼라인먼트 요구 사항 - 서스펜션