03/06/2024 16:55:10

Suspension - coussin du siège - siège du conducteur (retirez et remplacez)

Code de correction 13071122 0,60 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 2024-01-05: Rewrite the procedure according to the latest validation in which the driver seat cushion suspension is removed without removing the driver seat.
Tableau 1. Caractéristiques techniques de couple : Suspension - coussin du siège - siège du conducteur (retirez et remplacez)
Description Valeur de couple Outils recommandés Réutiliser/remplacer Remarques
Fixations du siège avant gauche (x4)
33.5 Nm (24.7 lbs-ft)
  • Douille Torx Plus T45
  • Clé à cliquet/Clé dynamométrique
  • Clé à cliquet sans fil/Visseuse à percussion
  • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
Remplacer Les boulons sont scellés
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les rebords de la base des sièges sont coupants et ils peuvent causer des blessures. Portez des gants résistants aux coupures lorsque vous retirez un siège du véhicule et lors de procédures qui nécessitent de travailler sur ou près d’une base de siège.

Retirer

  1. Open all doors and lower all windows.
  2. Remove the LH middle A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
  3. Remove the LH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
  4. Use a clip prytool to release the LH front seat harness from the sill trim clips (x5).
  5. Pull the LH front seat harness from under the LH front cabin carpet.
  6. Move the LH front seat forward, and then remove and discard the LH front seat rear fasteners (x2).
    Tip : Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à cliquet/Clé dynamométrique
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
  7. Move the LH front seat backward, and then remove and discard the LH front seat front fasteners (x2).
    Tip : Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à cliquet/Clé dynamométrique
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
  8. Tilt the LH front seat rearward to gain access to the underside of the LH front seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to disconnect the LH seat harness from the body controller. Take care when moving the seat. Ensure the carpet is not damaged.
  9. With assistance, remove the retaining clips (x4) under the main seat harness junction from the LH front seat frame.
  10. Move the LH front seat to most forward.
  11. Disconnect the LV power. See Alimentation 12 V/BT (déconnectez et connectez).
  12. With assistance, unhook the clips (x2) that attach the lower section of the seat back trim and move the seat back flap away from the working area.
  13. With assistance, release the clips (x2) that attach the seat cushion foam to the seat suspension.
  14. Disconnect the seatback heater connector, and then separate the connector from the seat underside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the connector straight down to release it from the seat assembly.
  15. Disconnect the seat cushion heat pad connector, and then separate the connector from the seat underside.
  16. Disconnect seat occupied sensor connector.
  17. Release the clip that attaches the seat occupied sensor to the seat underside, and then separate the sensor from the seat underside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the sensor from the seat frame by depressing the retaining clip and pulling the sensor away.
  18. Remove the clips (x2) that attach the seat occupied sensor connector and the LH seat harness to the seat cushion suspension.
  19. With assistance, remove the upper part of the LH front seat cushion suspension from the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Reversely use the clip prytool to remove the seat suspension. Press the seat suspension down with appropriate force to completely separate it from the seat frame.
  20. With assistance, remove the LH front seat cushion suspension from the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the seat suspension downwards to a horizontal position and lift it upwards to remove the lower part of the seat suspension.

Installer

  1. With assistance, install the lower part of the LH front seat cushion suspension to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clip the seat suspension to the seat frame in a horizontal position and then rotate upwards.
  2. With assistance, install the upper part of the LH front seat cushion suspension to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Reversely use the clip prytool to install the seat suspension. Press the seat suspension down with appropriate force to install it to the inside of the seat frame.
  3. Fasten the clip that attaches the seat cushion heat pad connector to the seat underside, and then connect the connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the connector onto the seat frame clip to secure.
  4. Fasten the clip that attaches the seatback heater connector to the seat underside, and then connect the connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the connector onto the seat frame clip to secure.
  5. Install the clips (x2) that attach the seat occupied sensor connector and the LH seat harness to the seat cushion suspension.
  6. Install the seat occupied sensor to the seat underside, and then fasten the clip that attaches the sensor to the seat underside.
  7. Secure the clip that attaches the seat occupied sensor to the seat assembly, and then connect occupied sensor electrical connector.
  8. Connect the LV power. See Alimentation 12 V/BT (déconnectez et connectez).
  9. Move the LH front seat to most rearward.
  10. With assistance, install the retaining clips (x4) under the main seat harness junction to the LH front seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of clips may vary.
  11. Fasten the clips (x2) that attach the seat cushion to the seat suspension.
  12. Attach the clips that attach the lower section of the seat back trim to the seat suspension.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the straps are tight for proper fit and installation.
  13. Return the LH front seat to the vertical position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care when moving the seat. Ensure the carpet is not damaged.
  14. Secure the LH front seat harness under the LH front cabin carpet.
  15. Install the LH front seat harness to the sill trim clips (x5).
  16. Install new LH front seat front fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Tip : Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à cliquet/Clé dynamométrique
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
  17. Move the LH front seat forward, and then install new LH front seat rear fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Tip : Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à cliquet/Clé dynamométrique
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
  18. Install the LH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
  19. Install the LH middle A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
  20. Move the LH front seat to original position.
  21. Raise all windows and close all doors.