26/01/2023 16:59:46

Faisceau - Carrosserie - Gauche (conduite à gauche) (retirez et remplacez)

Code de correction 17100802 2.64 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
  1. Open all four doors
  2. Lower all four windows
  3. Open liftgate
  4. Release 2nd row seat cushion
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift front edge of seat cushion upward to release foam from frame, Pull towards front of vehicle then tilt bench against 40/60 back
  5. Remove rear load floor
  6. Remove front load floor
  7. Remove trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  8. Remove LH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x tabs, 2x clips
  9. Remove LH trunk pocket bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 5x alignment tabs
  10. Fold the 60 seat in down position
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Protect the seat back upholstery if necessary, Do not put weight on seat in folded position without cushion present due to risk of bending the locator tab on the frame
  11. Release top edge of LH trunk side trim and disconnect 12V outlet and trunk switch connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 2x connectors, Trim part may slightly differ, by vehicle build location
  12. Release remaining clips and remove LH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar
  13. Remove LH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Guide front upper corner groove out from headliner and place trim aside
  14. Remove RH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x tabs, 2x clips
  15. Remove RH trunk pocket bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 5x alignment tabs
  16. Fold the 40 seat in down position
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Protect the seat cushion, Do not put weight on seat in folded position without cushion present due to risk of bending the locator tab on the frame
  17. Release clips and remove RH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 11x clips, Guide front clip stanchions around RH C-pillar
  18. Remove RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Guide front upper corner groove out from headliner and place trim aside
  19. Remove LH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
  20. Remove clip securing LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  21. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel
  22. Release LH front door seal from body
  23. Remove clip securing LH front cabin carpet to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  24. Pull LH front cabin carpet away from A-pillar to access LH front seat connector
  25. Move LH front seat forward
  26. Remove RH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
  27. Remove clip securing RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  28. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel
  29. Release RH front door seal from body
  30. Remove clip securing RH front cabin carpet to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  31. Pull RH front cabin carpet away from A-pillar to access RH front seat connector
  32. Move RH front seat forward
  33. Release seat belt retractor from RH front seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Insert special removal tool into the bottom of the retractor to release
  34. Release seat belt retractor from LH front seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Insert special removal tool into the bottom of the retractor to release
  35. Remove LH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Discard after removal
  36. Move LH front seat backward
  37. Remove LH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Discard after removal
  38. Adjust position of LH front seat for easy removal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Move seat to middle of track at most upright position
  39. Remove RH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Discard after removal
  40. Move RH front seat backward
  41. Remove RH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Discard after removal
  42. Adjust position of RH front seat for easy removal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Move seat to middle of track at most upright position
  43. Open hood
  44. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips
  45. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  46. Disconnect 12V negative terminal and first responders loop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x nut, 10mm, 6 Nm, 1x connector, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V, Negative terminal should be disconnected before FRL, Allow 2 minutes for all electrical circuits to fully discharge
  47. Disconnect LH front seat harness from VC left
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC left, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged
  48. Remove LH front seat harness from LH footwell support bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x retaining clips
  49. Release LH front seat harness from LH front sill panel harness bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  50. Pull LH front seat harness from under LH front cabin carpet
  51. Remove LH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim
  52. Disconnect RH front seat harness from VC right
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC right, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged
  53. Remove RH front seat harness from RH footwell support bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x retaining clips
  54. Release RH front seat harness from lower A 12V bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  55. Pull RH front seat harness from under RH front cabin carpet
  56. Remove RH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim
  57. Remove LH console side panel carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x guide pins, Use trim tool starting at top edge to release upper clips, then pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
  58. Remove LH front exterior hardware from center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 7 Nm
  59. Remove console lower rear panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  60. Remove LH rear exterior hardware from center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 7 Nm
  61. Remove RH rear exterior hardware from center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 7 Nm
  62. Remove RH console side panel carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    12x clips, 2x locating pins, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
  63. Remove RH front exterior hardware from center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 7 Nm
  64. Disconnect harness from rear of center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  65. Disconnect USB harness at right front of center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x USB connector
  66. Remove center console from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify rotating lids are in closed position, Recommend assistance, Tilt rear of console upward, Pull assembly towards rear of vehicle
  67. Release LH upper B-pillar assembly and move aside
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Pull the bottom of the upper B-pillar toward inside of the vehicle then pull the top to release the remaining clips
  68. Partially remove LH rear door seal
  69. Remove LH rear sill trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim, Trim part may slightly differ, by vehicle build location
  70. Remove clip securing LH lower B-pillar to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, Clip secures lower B-pillar and rear cabin carpet to body
  71. Remove the LH lower B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Pull the top of B-pillar to release top clips then work your way to bottom clips
  72. Release clips securing the RH upper B-pillar assembly and move aside
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips
  73. Partially remove RH rear door seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pillar and sill trim have tabs seated underneath seal
  74. Remove RH rear sill trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of RH rear sill trim working your way back towards rear of sill trim
  75. Remove clip securing RH lower B-pillar to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, Clip secures lower B-pillar and rear cabin carpet to body
  76. Remove the RH lower B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Pull the top of B-pillar to release top clips then work your way to bottom clips
  77. Remove rear floormat
  78. Remove clips securing rear main cabin carpet to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x push clips
  79. Remove rear main cabin carpet from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull up at the rear of rear main carpet and slide back, Remove from LH rear door
  80. Remove screw and clips securing LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clips, 1x screw, T20, 2.5 Nm
  81. Remove connectors from LH footwell cover and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x tabs, 1x Ethernet connector, 1x puddle light connector
  82. Remove fasteners securing driver knee air bag to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clips, 2x screws, T20, 2 Nm, 4x patch bolts, E10, 8 Nm, Discard after removal, Support the knee air bag while lowering, The connector / harness length is very short
  83. Disconnect the driver knee air bag and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release locking tab, Then release squib from air bag, Support air bag while disconnecting, Connector release may vary
  84. Remove the LH footwell air duct
  85. Remove LH front floormat
  86. Remove clips securing LH front cabin carpet to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips
  87. Remove LH front cabin carpet from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift up rear edge of carpet then slide out towards rear of vehicle, be cautious and avoid foam below catching on seat risers
  88. Remove LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove
  89. Remove LH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Extending the sun visor may allow for extra working room
  90. Remove LH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  91. Remove LH sun visor from headliner area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fold sun visor to the closed and folded down position but do not latch in place
  92. Disconnect LH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  93. Remove RH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
  94. Remove RH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Extending the sun visor may allow for extra working room
  95. Remove RH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  96. Remove RH sun visor from headliner area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fold sun visor to the closed and folded down position but do not latch in place
  97. Disconnect RH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  98. Remove lower quad cam cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x tabs, Press on the side of the cover with a trim tool to release some of the tabs
  99. Remove tether from lower quad cam cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x hook, Guide hook through anchor on quad cam cover
  100. Disconnect rear view mirror connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  101. Remove rear view mirror
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T20, 2.5 Nm
  102. Push open LH coat hook
  103. Open LH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking tab
  104. Remove LH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 1.0 Nm
  105. Push open RH coat hook
  106. Open RH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking tab
  107. Remove RH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 1.0 Nm
  108. Release headliner from body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, Recommend assistance, Headliner will be partially supported by safety tethers at B-pillars and 2x tether clips at rear corners
  109. Disconnect J5 body connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release lock then remove
  110. Disconnect J2 body connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release lock then remove
  111. Disconnect J4 body connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release lock then remove
  112. Disconnect brake switch
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  113. Disconnect accelerator pedal connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector
  114. Remove accelerator and brake pedal harness clips
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  115. Disconnect headliner harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  116. Disconnect white connector X909 from front harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  117. Remove LH body harness clips from LH A-pillar
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  118. Release clips securing for LH body harness from below LH front seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  119. Remove LH harness clips under front seats and center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  120. Disconnect LH body harness from RCM
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  121. Disconnect LH harness from RH body Harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors,1x clip,Release red locking tabs
  122. Disconnect the LH body harness connectors around lower B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x connectors, LH rear door harness, acceleration sensor, and LH seat belt
  123. Remove the LH harness ground strap around LH lower B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 10 Nm
  124. Remove LH harness clips from B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips
  125. Release LH B-pillar applique from body to disconnect camera connector then remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x fir tree clip, 2x clips, 2x connectors, Pull straight outwards to release from B-Pillar, Use caution not to damage the connectors
  126. Remove the LH body harness clips around the below C-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  127. Disconnect logic connector at LH seat frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  128. Disconnect LH 2nd row retractor connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 2 stage locking connector, Lift the red locking tab then release the connector
  129. Remove the LH body harness clips around C-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  130. Disconnect LH side curtain air bag and liftgate power strut electrical connector from LH body harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  131. Release connectors from LH body harness to charge port ECU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  132. Remove LH body harness clips around LH side trunk area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  133. Disconnect connectors from chargeport assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors, 1x red locking tab, 2x white locking tab
  134. Remove the LH body harness ground strap below LH tail lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 10 Nm
  135. Remove LH liftgate stop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x liftgate stop, Pull up to remove
  136. Disconnect LH rear bodyside tail lamp assembly connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
  137. Remove nuts securing LH rear bodyside tail lamp assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 8mm, 3.2 Nm
  138. Remove LH rear bodyside tail lamp assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x studs, To ease removal use trim tool to release lamp from body near each stud. While releasing studs, Pull from opposite end of lamp.
  139. Remove bolt securing LH corner of rear fascia to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 4 Nm
  140. Remove RH liftgate stop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x liftgate stop, Pull up to remove
  141. Disconnect RH rear bodyside tail lamp assembly connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
  142. Remove nuts securing RH rear bodyside tail lamp assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 8mm, 3.2 Nm
  143. Remove RH rear bodyside tail lamp assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x studs
  144. Remove bolt securing RH corner of rear fascia to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 4 Nm
  145. Release rear fascia from rear diffuser
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 7x bolts, 10mm, 4 Nm
  146. Remove LH rear fender garnish from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips, Release from center of garnish and work your way outward towards both ends, Using clip prytool release yellow clips at rear of fascia to avoid damage to garnish
  147. Remove bolt securing LH rear fascia to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 8mm, 4 Nm
  148. Remove RH rear fender garnish from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips, Release from center of garnish and work your way outward towards both ends, Using clip prytool release yellow clips at rear of fascia to avoid damage to garnish
  149. Remove bolt securing RH rear fascia to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 8mm, 4 Nm
  150. Release rear fascia from body and disconnect rear fascia harness then remove assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Slide red locking tab away from connector, Then depress black locking tab to release the connector. Recommend assistance, Place rear fascia on padded surface to avoid damage
  151. Remove rear body harness from rear fascia center bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  152. Disconnect rear BLE
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 2 stage locking connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
  153. Disconnect rear subframe and LH rear EPB connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  154. Push the rear subframe portion of the LH body harness through the LH side trunk bulkhead
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Harness passes through into trunk near rear section of LH rear wheel liner area
  155. Remove the LH body harness from vehicle
  156. Position the LH body harness into vehicle for installation
  157. Push the rear harness seal through body and fully seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Harness passes through into trunk near rear section of LH rear wheel liner area
  158. Connect rear subframe and LH rear EPB connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  159. Connect rear BLE
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage locking tab
  160. Install rear body harness onto rear fascia center bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  161. Connect and install rear fascia onto vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage red locking tab, Recommend assistance, Verify lower portion aligns with rear diffuser
  162. Apply Loctite 222 onto rear diffuser bolts and secure rear fascia to rear diffuser
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 7x bolts, 10mm, 4 Nm
  163. Install bolt securing RH rear fascia to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 8mm, 4 Nm
  164. Install RH rear fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  165. Install bolt securing LH rear fascia to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 8mm, 4 Nm
  166. Install LH rear fender garnsih
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  167. Install bolt securing RH corner of rear fascia
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 4 Nm
  168. Remove RH bodyside lamp connector gasket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  169. Install RH bodyside lamp connector gasket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  170. Remove upper T-stud gasket from RH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  171. Install upper T-stud gasket to RH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  172. Remove lower T-stud gasket from RH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  173. Install lower T-stud gasket to RH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  174. Install RH rear bodyside tail lamp assembly into vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x studs
  175. Install nuts securing RH rear bodyside tail lamp assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 8mm, 3.2 Nm
  176. Connect the RH rear bodyside tail lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage locking tab
  177. Install RH liftgate stop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x liftgate stop, Align tab and push down to secure
  178. Install bolt securing LH corner of rear fascia
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 4 Nm
  179. Remove LH bodyside lamp connector gasket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  180. Install LH bodyside lamp connector gasket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  181. Remove upper T-stud gasket from LH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  182. Install upper T-stud gasket to LH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  183. Remove lower T-stud gasket from LH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  184. Install lower T-stud gasket to LH bodyside lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x gasket
  185. Install LH rear bodyside tail lamp assembly into vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x studs
  186. Install nuts securing LH rear bodyside tail lamp assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 8mm, 3.2 Nm
  187. Connect the LH rear bodyside tail lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage locking tab
  188. Install LH liftgate stop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x liftgate stop, Align tab and push down to secure
  189. Install the LH body harness ground strap below LH tail lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 10 Nm
  190. Install logic connectors to charge port assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors, 1x red locking tab, 2x white locking tab
  191. Install LH body harness clips around LH side trunk area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  192. Install connectors from LH body harness to charge port ECU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  193. Connect LH side curtain air bag and liftgate power strut electrical connector to LH body harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  194. Install the LH body harness clips around upper C-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  195. Connect LH 2nd row retractor connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 2 stage locking connector, Engage the red locking tab when the connector is fully seated
  196. Connect logic connector at LH 60 seat frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  197. Install the LH body harness clips around the below C-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  198. Connect camera connector then install LH B-pillar applique to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, 1x fir tree clip, 2x clips, Align B-Pillar applique into position and secure clips into body, Use caution not to damage the connectors
  199. Install LH harness clips onto B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips
  200. Connect the LH body harness connectors around lower B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x connectors, LH rear door harness, acceleration sensor, and LH seat belt
  201. Install the LH harness ground strap around LH lower B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 10 Nm
  202. Connect LH harness to RH body Harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connector,1x clip,Engage locking tabs
  203. Install LH body harness to RCM
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  204. Install LH harness clips under LH front seat and RH lower B-pillar area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  205. Install securing clips LH body harness beiow LH front seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  206. Install LH body harness clips to LH A-pillar
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  207. Connect J5 body connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Fully seat connector then engage lock
  208. Connect J2 body connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Fully seat connector then engage lock
  209. Connect J4 body connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Fully seat connector then engage lock
  210. Connect white connector X909 to front harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  211. Connect headliner harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  212. Install accelerator and brake pedal harness clips
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  213. Connect accelerator pedal connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage locking tab
  214. Connect brake switch connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  215. Install the LH footwell duct into HVAC module
  216. Connect the driver knee air bag and install into vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector
  217. Install fasteners securing driver knee air bag to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 2x push clips
  218. Install headliner to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, Recommend assistance, Seat 2x clips at coat hooks when replacing headliner, Reseat primary seal at doors and liftgate to headliner
  219. Install rear view mirror
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T20, 2.5 Nm
  220. Connect rear view mirror connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  221. Install tether onto lower quad cam cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x hook, Guide hook through anchor on quad cam cover
  222. Install quad camera lower cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x tabs, Install the tabs closest to the rearview mirror assembly and push the cover up to secure
  223. Connect RH sun visor connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  224. Install RH sun visor into headliner area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fold sun visor to the closed and folded down position but do not latch in place
  225. Install RH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 3.5 Nm
  226. Install RH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  227. Install RH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  228. Connect LH sunvisor connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  229. Install LH sun visor into headliner area
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fold sun visor to the closed and folded down position but do not latch in place
  230. Install LH sun visor fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 3.5 Nm
  231. Install LH sun visor bracket cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  232. Install LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  233. Install LH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 1.0 Nm
  234. Close LH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking tab
  235. Push LH coat hook closed
  236. Install RH coat hook screw
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 1.0 Nm
  237. Close RH coat hook screw cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking tab
  238. Push RH coat hook closed
  239. Install LH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarter glass, Seat trunk seal to edge of trim
  240. Position LH trunk side trim and install lower clips
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clips, 5x clips, Guide front clip stanchions around LH C-pillar
  241. Connect 12V outlet and trunk switch connector and seat top edge of LH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 2x connectors
  242. Install LH trunk pocket bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 5x alignment tabs
  243. Install LH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x tabs, 2x clips
  244. Install RH upper C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarterglass, Seat trunk seal to edge of trim
  245. Install RH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 11x clips, Guide front clip stanchions around RH C-pillar
  246. Install RH trunk pocket bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 5x alignment tabs
  247. Install RH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x tabs, 2x clips
  248. Install front load floor
  249. Install rear load floor
  250. Install trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Seat seal around edge of trim
  251. Fold the 60 seat into vertical position
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove seat back protection if necessary
  252. Fold 40 seat into vertical position
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove seat cushion protection
  253. Install rear main cabin carpet to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Position rear main carpet to floorboard and slide forward, Ensure rear main carpet tucks beneath front main carpet and air duct
  254. Install clips securing rear main cabin carpet to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x push clips
  255. Install rear floormat
  256. Install LH front cabin carpet
  257. Install clips securing the LH front cabin carpet to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips
  258. Install connectors to LH footwell cover and position for installation
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x tabs, 1x Ethernet connector, 1x puddle light connector
  259. Install screw and clips securing LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 2.5 Nm, 2x push clips
  260. Install the RH lower B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips
  261. Install clip securing RH lower B-pillar to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, Clip goes through B-pillar and rear cabin carpet
  262. Install RH rear sill trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips
  263. Install the RH upper B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim
  264. Install the LH lower B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips
  265. Install clip securing LH lower B-pillar to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, Clip secures lower B-pillar and rear cabin carpet to body
  266. Install LH rear sill trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of LH rear sill trim into trunk side trim and work your way forward securing clips, Trim part may slightly differ, by vehicle build location
  267. Reseat LH rear door seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Seat pillar and sill trim tabs underneath seal
  268. Reposition 2nd row seat cushion
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide cushion rearward then align with buckles and foam with seat rail, Make sure cushion is fully seated with push & pull test
  269. Install the LH upper B-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim
  270. Install center console onto vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place
  271. Connect harness at right front of center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x USB connector
  272. Connect harness to rear of center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  273. Install RH front exterior hardware to center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 7 Nm
  274. Install RH console side panel carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    12x clips, 2x locating pins, Position side panel and align the front locator, then the rear locator, Push side panel towards console to install
  275. Install RH rear exterior hardware to center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 7 Nm
  276. Install LH rear exterior hardware to center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 7 Nm
  277. Install console lower rear panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  278. Install LH front exterior hardware to center console
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 7 Nm
  279. Install LH console side panel carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install
  280. Install LH front seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim
  281. Secure LH front seat harness under LH front cabin carpet
  282. Install LH front seat harness along LH front sill panel harness bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  283. Install LH front seat harness onto LH footwell support bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips
  284. Connect LH front seat harness to VC left
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x electrical connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated
  285. Fully seat LH front cabin carpet
  286. Install clip securing LH front cabin carpet to body
  287. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 2 locating pins, Align front locating pin first
  288. Install clip securing LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  289. Install LH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
  290. Reseat LH front door seal along lower A-pillar trim
  291. Install RH front seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim
  292. Secure RH front seat harness under RH front cabin carpet
  293. Install RH front seat harness along plastic guide
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  294. Install RH front seat harness onto RH footwell support bracket
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x retaining clips
  295. Connect RH front seat harness to VC right
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x electrical connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated
  296. Fully seat RH front cabin carpet
  297. Install clip securing RH front cabin carpet to body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  298. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 2x locating pins, Align front locating pin first
  299. Install clip securing RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  300. Install RH mid A-pillar assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Make sure the seal seat on top of the trim
  301. Reseat RH front door seal along lower A-pillar trim
  302. Connect first responder loop and 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x nut, 10mm, 6 Nm, 1x connector, Engage locking tab, Connect FRL first before connecting 12V to avoid damage to car computer
  303. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
  304. Close hood
  305. Move LH front seat backward
  306. Install LH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Install new patch bolts
  307. Move LH front seat forward
  308. Install LH front seat belt retractor to seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test
  309. Install LH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Install new patch bolts
  310. Move LH front seat to original position
  311. Move RH front seat backward
  312. Install RH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Install new patch bolts
  313. Move RH front seat forward
  314. Install RH front seat belt retractor to seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test
  315. Install RH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, T45P, 33.5 Nm, Install new patch bolts
  316. Move RH front seat to original position
  317. Close liftgate
  318. Raise all four windows
  319. Close all four doors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If 12V is powered up, Unlatch rear doors before closing