2025-03-23

Faisceau - filtre de climatiseur - batterie HT (Ensemble non-structurel) (retirez et remplacez)

Code de correction 16305322 2.88 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.

  • 2025-03-21: Updated resistance measurement information at the AC filter harness assembly.

Retirer

  1. Remove the ancillary bay cover. See Couvercle - baie auxiliaire (retirer et remplacer).
  2. Install the HV battery insulators. See Isolateurs - Batterie HT (Installation et retrait).
  3. Remove the HV battery skid plate. See Plaque de protection - batterie HT - arrière (retirez et remplacez).
  4. Drain the ancillary bay coolant. See Liquide de refroidissement des baies auxiliaires (vidange et remplissage).
  5. Remove the pyrotechnic battery disconnect. See Sectionneur de batterie pyrotechnique (retirez et remplacez).
  6. Remove the DC input assembly from the ancillary bay. See Ensemble d’entrée CC - batterie HT (type barre omnibus) (retirez et remplacez).
  7. Remove the bolts (x2) and nut that secure the fast charge assembly to the ancillary bay.
    5.5 Nm (4.1 lbs-ft)
    8 Nm (5.9 lbs-ft)
  8. Remove the negative AC inlet terminal cover.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips.
  9. Remove and discard the bolt that secures the negative AC inlet terminal to the negative inlet fast charge busbar.
    4.4 Nm (3.2 lbs-ft)
  10. Remove the positive AC inlet terminal cover.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips.
  11. Remove and discard the bolt that secures the positive AC inlet terminal to the positive inlet fast charge busbar.
    4.4 Nm (3.2 lbs-ft)
  12. Remove the clip that secures the AC filter harness to the fast charge assembly.
  13. Remove the AC filter harness.

Installer

  1. Install the clip that secures the AC filter harness to the fast charge assembly.
  2. Install the bolt that secures the positive AC inlet terminal to the positive inlet fast charge busbar.
    4.4 Nm (3.2 lbs-ft)
  3. Install the bolt that secures the negative AC inlet terminal to the negative inlet fast charge busbar.
    4.4 Nm (3.2 lbs-ft)
  4. Measure the resistance at the points indicated on the AC filter harness assembly. Measured resistance should be 150 𝜇Ω or less.
    • Negative AC inlet terminal and negative inlet side fast charge busbar
    • Positive AC inlet terminal and positive inlet side fast charge busbar
  5. Install the negative AC inlet terminal cover.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips.
  6. Install the positive AC inlet terminal cover.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips.
  7. Position the fast charge assembly onto the ancillary bay for installation.
  8. Install the bolts (x2) and nut that secure the fast charge assembly to the ancillary bay.
    5.5 Nm (4.1 lbs-ft)
    8 Nm (5.9 lbs-ft)
  9. Install the DC input assembly to the ancillary bay. See Ensemble d’entrée CC - batterie HT (type barre omnibus) (retirez et remplacez).
  10. Perform an ancillary bay coolant leak test. See Test d'étanchéité du liquide de refroidissement des baies auxiliaires.
  11. Install the HV battery skid plate. See Plaque de protection - batterie HT - arrière (retirez et remplacez).
  12. Connect the 12V auxiliary battery negative terminal only.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    DO NOT reconnect the first responder loop at this time.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Do not follow the procedure to connect 12V power at this time.
  13. Connect a 12V charger to the 12V auxiliary battery terminals.
  14. Refill the coolant to the MAX line.
  15. Connect a laptop with Toolbox to the vehicle.
  16. In Toolbox, type "vcfront" into the search field.
  17. Click the "play" button next to TEST-RESET_VCFRONTvia Toolbox: (link)via Service Mode Plus:
    • Low Voltage ➜ Power Distribution ➜ Reset VCFRONT
    • Mid Voltage ➜ Power Distribution ➜ Reset VCFRONT
    , and then select RUN.
  18. Click the "play" button next to TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    , and then select RUN.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure the vehicle is not in Drive.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The test will last for approximately 10 minutes. Monitor and keep the superbottle topped off while the test is running. Coolant pump speeds can be monitored in Service Mode + (see Mode Entretien Plus), in the CAN Viewer submenu. If pump speeds stay above 6900 rpm, there is still air entrapped in the system; run a cooling system vacuum refill.
  19. Refill the coolant to the MAX line.
  20. Install the coolant bottle cap.
  21. Power off the vehicle from the touchscreen.
  22. Remove the 12V charger from the 12V auxiliary battery terminals.
  23. Disconnect the 12V auxiliary battery negative terminal.
  24. Put on PPE including the HV insulating gloves and leather over gloves.
  25. Install the pyrotechnic battery disconnect.. See Sectionneur de batterie pyrotechnique (retirez et remplacez).
  26. Remove the HV battery insulators. See Isolateurs - Batterie HT (Installation et retrait).
  27. Install the ancillary bay cover. See Couvercle - baie auxiliaire (retirer et remplacer).