Couvercle B - 2e rangée - intérieur - gauche (7-places) (retirez et remplacez)
Code de correction 13084212 0.66 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.
- Open RH front and rear doors
- Lower all four windows
- Move LH front seat forward
- Move RH front seat forward
-
Partially remove LH rear door seal
-
Remove LH 7s Lower C-Pillar Trim
Remarque8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
-
Fold 60 seat into down position
-
Disconnect logic connector at LH seat frame
Remarque1x connector
-
Move 60 seat forward using towel bar
RemarqueWith one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove 60 seat rear outboard track fastener
Remarque1x patch bolt, 11mm, 37 Nm, Discard after removal
-
Remove 60 seat rear inboard track fasteners
Remarque2x patch bolts, 11mm, 37 Nm, Discard after removal
-
Move 60 seat fully rearward using towel bar
RemarqueWith one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove 60 seat outboard track cover
Remarque1x clip, Slide covers forward to release from 60 seat tracks
-
Remove center track cover from 2nd row seats
Remarque2x clips, Slide covers forward to release from 2nd row seat tracks
-
Release cabin carpet from 60 seat
RemarquePull cabin carpet towards front of vehicle
-
Remove 60 seat front inboard track fasteners
Remarque1x bolts, 11mm, 37 Nm, Discard after removal
-
Remove 60 seat front outboard track fasteners
Remarque1x bolts, 11mm, 37 Nm, Discard after removal
-
Remove 2nd row 60 seat assembly from vehicle
RemarqueRecommend assistance
-
Remove front push clip from 60 outer sideshield assembly
Remarque1x clip, Use pick to remove the push clip from the bottom side of the outboard cover
-
Remove 60 outer sideshield assembly
Remarque1x clip 1x connector, Remove outer sideshield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection
-
Remove 60 seat toe kick cover
Remarque7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove
-
Release clips and remove inboard outer trim from 60 seat
Remarque3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle
-
Remove 60 seatback panel
Remarque9x clips, 2x hooks, Release clips starting at the top of backpanel working your way down the lower backpanel, pull 60 backpanel towards front of vehicle to remove
-
Remove 2nd row center seat switch
Remarque1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 backpanel to ease removal
-
Remove center backpanel from center seatback
Remarque5x clips, 2 hooks, Lift up at the lower 20 backpanel and then slide forward to release
-
Release 60 seat harness connectors and clip from seat from seat frame
Remarque1x clip, 7x connectors
-
Disconnect seat cables from easy entry actuators on 60 seat
Remarque4x clips
-
Remove push clips for 60 bottom seat pan
Remarque2x clips, Remove push clips from front of seat pan
-
Remove center seatback lumbar bun fastener
Remarque1x screw, T20, 1.5 Nm
-
Remove center seatback lumbar bun
Remarque2x clips, Pull bolster outwards to release
-
Remove center seatback pivot clamps
Remarque2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove
-
Remove center seatback from 60 seat frame
RemarqueRemove center seatback by lifting upwards
-
Manually release the center seatback latch
RemarqueUse small screwdriver to manipulate the center seatback latch to release
-
Remove fasteners securing 60 seat pan to seat frame
Remarque4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame
-
Remove headrest from 60 seat assembly
RemarqueSimultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged
-
Remove headrest guides from 60 seat
RemarquePull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides
-
Remove 60 seatback
Remarque4x clips, Release clips securing 60 seatback and lift upwards
-
Remove 60 seat bottom
RemarqueRemove seat bottom by lifting the rear first and removing it towards front of the seat
-
Remove push clip from trim
Remarque1x clip, Remove trim clip from cover
-
Remove center inner cover
Remarque2x clips, Pry center inner cover back to disengage clips, Remove by lifting up while pulling back
-
Remove 60 B-Cover I/B Inner
-
Install 60 B-Cover I/B Inner trim
-
Install center inner cover
Remarque2x clips, Install inner cover ensuring the clips seat to outer cover
-
Install push clip to trim
Remarque1x clip
-
Place 60 seat pan onto seat frame
RemarqueReinstall seat bottom onto seat frame by starting at the rear of the seat
-
Secure 60 seat bottom to seat frame
Remarque4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame
-
Install headrest guides into 60 seat assembly
RemarqueInstall headrest guides by pressing downwards until lower tab is seated
-
Install 60 seat back into place
Remarque4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back
-
Install headrest onto 60 seat assembly
RemarquePush down to secure
-
Install center seatback pivot clamps
Remarque2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs
-
Install center seatback lumbar bun fastener
Remarque1x screw, T20, 1.5 Nm
-
Plug in connector and install trim to 60 seat
Remarque1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.
-
Install push clip at front of outer 60 sideshield assembly
Remarque1x clip, Install push clip at front bottom side of the trim
-
Install inboard outer trim to 60 seat
RemarqueClips 3x, Install inboard outer trim and reseat 3x clips
-
Insert backpanel hooks into center seat back assembly
Remarque2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks
-
Install center backpanel onto seat back
Remarque5x clips
-
Install 2nd row center seat switch
Remarque1x connector, 2x clips
-
Install 60 toe kick cover
Remarque7x clips
-
Install LH seatback onto 60 seat assembly
Remarque9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips
-
Connect logic connector at LH 60 seat frame
Remarque1x connector
-
Install fasteners securing 60 seat frame to body
Remarque5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front
-
Secure cabin carpet to 60 seat
RemarqueStrap velcro on
-
Fold the 60 seat into vertical position
RemarqueRemove seat back protection if necessary
-
Install 60 seat outboard track cover
Remarque1x clip
-
Install 60 seat outboard track cover
Remarque1x clip
-
Install LH 7s Lower C-Pillar Trim
Remarque8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
-
Reseat LH rear door seal
RemarqueSeat pillar and sill trim tabs underneath seal
- Move RH front seat to original position
- Raise all four windows
-
Close all four doors
RemarqueIf 12V is powered up, Unlatch rear doors before closing