Module - commande de la carrosserie - sécurité (retirez et remplacez)
Code de correction
17454002 0.42 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.
- 2025-03-10: Updated post-replacement routine.
- 2024-01-17: Added step for ODIN routine to be run for vehicles running certain firmware versions.
- 2023-11-20: Updated security controller configuration steps.
- 2023-10-24: Updated post-replacement Toolbox routines.
- 2023-07-21: Added Note about security-related toolbox actions.
- 2024-07-17: Updated the way of performing the routines from using Toolbox to using the touchscreen.
Caractéristiques techniques de couple
Description | Valeur de couple | Outils recommandés | Réutiliser/remplacer | Remarques |
---|---|---|---|---|
Vis qui fixent le module contrôleur de carrosserie de sécurité au panneau décoratif du porte-gobelet |
![]() 1.6 Nm (1.2 lbs-ft) |
|
Réutiliser | |
Vis (x4) qui fixent la bande lumineuse gauche de la console centrale à la console centrale |
![]() 1.6 Nm (1.2 lbs-ft) |
|
Réutiliser |
Retirer
-
Open all doors and lower all windows.
NoteLatch the rear doors with the doors open using a small flat blade screwdriver to prevent an accidental lockout.
- Move the driver seat and front passenger seat fully rearward and to the lowest position.
- Disconnect 12V power. See Alimentation 12 V/BT (déconnectez et connectez).
- Open the front and rear console rotating lids.
- Open the center console armrest fully.
- Release the clips (x4) that attach the rear of the LH decor trim to the center console assembly
-
Remove the screws (x4) that attach the rear of LH center console bright strip to the center console assembly.
TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Release the tabs (x3) that attach the rear of the LH center console bright strip to the center console assembly, and then partially release the bright strip from the assembly.
- Repeat step 6through step 8 for the RH side of the center console.
- Release the clips (x6) that attach the cup holder decor panel to the cup holder assembly, and then separate the cup holder decor panel from the center console assembly.
- Disconnect the electrical connector from the security body controller module, and then remove the cup holder decor panel from the vehicle.
-
Remove the screws (x2) that attach the security body controller module to the cup holder decor panel, and then remove the security body controller module from the panel.
TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Clé à rochet/Clé dynamométrique
- TorqueVario Wiha-S 0,80Nm - 2,0Nm
- Wiha, adaptateur d'embout ¼ po
Installer
-
Install the screws (x2) that attach the security body controller module to the cup holder decor panel.1.6 Nm (1.2 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Clé à rochet/Clé dynamométrique
- TorqueVario Wiha-S 0,80Nm - 2,0Nm
- Wiha, adaptateur d'embout ¼ po
- Connect the electrical connector to the security body controller module.
- Attach the clips (x6) that attach the cup holder decor panel to the center console assembly.
- Install the RH center console bright strip to the center console assembly.
-
Install the screws (x4) that attach the RH center console bright strip to the center console assembly.1.6 Nm (1.2 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Install the RH decor trim onto the center console assembly
- Repeat step 4 through step 6 for the LH side of the center console.
- Close the center console armrest.
- Close the rear and front console rotating lids.
- Reconnect 12V power. See Alimentation 12 V/BT (déconnectez et connectez).
- Restore the driver seat and front passenger seat back to their original position.
- Reinstall the vehicle firmware. See Réinstallation du logiciel – Écran tactile.
- Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : PROC_VCSEC_X_POST-REPLACEMENT-PROCEDUREvia Toolbox: (link)via Service Mode: Low Voltage ➜ Keys ➜ VCSEC Post Replacementvia Service Mode Plus: LowVoltage ➜ VCSEC Post Replacement ➜ VCSEC Post Replacement Procedure
- Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : PROC_VCSEC_C_PAIR-NFC-CARD-V2via Toolbox: (link)via Service Mode: Low Voltage ➜ Keys ➜ Pair Key
- Place the NFC card(s) on the NFC card reader in the center console, and check the function of the programmed NFC keys.
- Exit Service Mode. See Mode Entretien.
- Raise all windows and close all doors.
- Inform the customer that the new security body controller will not recognize any previously paired phone key. The customer must delete and re-pair their phone key to the vehicle, if they were previously using this feature. Instructions are available in the Owners Manual, and at the DIY web pages.