Ensemble pour garniture (retirez et remplacez)
Code de correction 152031021.26 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.
- 2023-05-19: Added headliner shipping bag installation tip.
- Open all four doors
- Lower all four windows
- Open liftgate
-
Remove LH IP end cap
Remarque3x clips
-
Remove LH mid A-pillar assembly
Remarque1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
-
Remove LH upper A-pillar trim
Remarque3x clips, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove
-
Remove clip securing LH lower A-pillar trim
Remarque1x push clip
-
Remove LH lower A-pillar trim
Remarque6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel
-
Remove LH sun visor bracket cover
Remarque4x clips, Extending the sun visor may allow for extra working room
-
Remove LH sun visor fastener
Remarque1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
-
Remove LH sun visor from headliner area
RemarqueFold sun visor to the closed and folded down position but do not latch in place
-
Disconnect LH sun visor connector
Remarque1x connector
- Move LH front seat forward
-
Remove RH IP end cap
Remarque3x clips
-
Remove RH mid A-pillar assembly
Remarque1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
-
Remove RH upper A-pillar trim
Remarque3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
-
Remove RH sun visor bracket cover
Remarque4x clips, Extending the sun visor may allow for extra working room
-
Remove RH sun visor fastener
Remarque1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
-
Remove RH sun visor from headliner area
RemarqueFold sun visor to the closed and folded down position but do not latch in place
-
Disconnect RH sun visor connector
Remarque1x connector
- Move RH front seat forward
-
Remove 2nd row seat cushion
Remarque1x connector, Lift front edge of seat cushion upward to release foam from frame
-
Partially remove LH rear door seal
-
Remove LH rear sill trim
Remarque5x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim, Trim part may slightly differ, by vehicle build location
-
Push open LH coat hook
-
Open LH coat hook screw cover
Remarque1x locking tab
-
Remove LH coat hook screw
Remarque1x screw, T20, 1.0 Nm
-
Release LH upper B-pillar assembly and move aside
Remarque4x clips, Pull the bottom of the upper B-pillar toward inside of the vehicle then pull the top to release the remaining clips
-
Remove rear load floor
-
Remove front load floor
-
Remove trunk sill trim
Remarque4x clips
-
Remove LH load floor bracket
Remarque3x tabs, 2x clips
-
Remove LH trunk pocket bracket
Remarque1x push clip, 5x alignment tabs
-
Release top edge of LH trunk side trim and disconnect 12V outlet and trunk switch connectors
Remarque6x clips, 2x connectors, Trim part may slightly differ, by vehicle build location
-
Release remaining clips and remove LH trunk side trim
Remarque1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar
-
Remove LH upper C-pillar trim
Remarque6x clips, Guide front upper corner groove out from headliner and place trim aside
-
Partially remove RH rear door seal
RemarquePillar and sill trim have tabs seated underneath seal
-
Remove RH rear sill trim
Remarque5x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of RH rear sill trim working your way back towards rear of sill trim
-
Push open RH coat hook
-
Open RH coat hook screw cover
Remarque1x locking tab
-
Remove RH coat hook screw
Remarque1x screw, T20, 1.0 Nm
-
Release clips securing the RH upper B-pillar assembly and move aside
Remarque4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips
-
Remove RH load floor bracket
Remarque3x tabs, 2x clips
-
Remove RH trunk pocket bracket
Remarque1x push clip, 5x alignment tabs
-
Release clips and remove RH trunk side trim
Remarque1x push clip, 11x clips, Guide front clip stanchions around RH C-pillar
-
Remove RH upper C-pillar trim
Remarque6x clips, Guide front upper corner groove out from headliner and place trim aside
-
Disconnect headliner harness
Remarque1x connector
-
Remove headliner harness clips from LH A-pillar area
Remarque6x clips
-
Release headliner from body
Remarque11x clips, Recommend assistance, Headliner will be partially supported by safety tethers at B-pillars and 2x tether clips at rear corners
-
Disconnect LH rear map light and release from rear portion of headliner
Remarque1x connector, 1x harness clip
-
Disconnect RH rear map light and release from rear portion of headliner
Remarque1x connector, 1x harness clip
-
Remove fasteners joining front and rear headliner trim
Remarque10x screws, T20, 1.0 Nm
-
Remove front headliner from vehicle
RemarqueRecommend assistance, Remove through front door, Place headliner on clean surface
-
Release LH rear headliner tether from roof clip
Remarque1x screw, T20, 1.5 Nm
-
Release RH rear headliner tether from roof clip
Remarque1x screw, T20, 1.5 Nm
-
Remove rear headliner from vehicle
Remarque2x tether clips, Recommend assistance, Remove through rear door, Place headliner on clean surface
-
Remove LH coat hook tether clip from body
Remarque1x clip
-
Remove RH coat hook tether clip from body
Remarque1x clip
-
Separate new headliner into front and rear
Remarque10x screws, T20, 1.0 NmConseil : Le sac d’expédition pour garniture de toit peut-être pratique et servir de « troisième main » pour l’installation.
- Mettez le sac à plat avec son ouverture vers vous.
- À l’aide de ciseaux, coupez vers le haut au centre à partir du haut et du bas jusqu’à ce qu’il reste environ 12 po (30 cm). Le sac ressemblera à un pantalon.
- Ouvrez les portes avant/arrière du véhicule (selon le besoin), placez le sac sur le toit du véhicule et faites entrer les « jambes » du sac dans l’habitacle pas les ouvertures de porte.
- Nouez les extrémités du sac de façon à créer une boucle lâche qui passe au-dessus du toit et dans l’habitacle. Si la boucle est trop serrée, coupez un peu plus au centre.
- Utilisez la boucle pour soutenir la garniture de toit lors de l’installation. Si la boucle est trop lâche, ajoutez un nœud.
-
Place rear headliner into vehicle
Remarque2x tether clips, Recommend assistance, Install through rear door
-
Place front headliner into vehicle
RemarqueRecommend assistance, Install through front door
-
Install fasteners joining front and rear headliner trim
Remarque10x screws, T20, 1.0 Nm, Recommend assistance
-
Connect RH rear map light and secure to rear portion of headliner
Remarque1x connector, 1x harness clip
-
Connect LH rear map light and secure to rear portion of headliner
Remarque1x connector, 1x harness clip
-
Install headliner to body
Remarque11x clips, Recommend assistance, Seat 2x clips at coat hooks when replacing headliner, Reseat primary seal at doors and liftgate to headliner
-
Install headliner harness clips to A-pillar area
Remarque6x clips
-
Connect headliner harness
Remarque1x connector
-
Install LH upper C-pillar trim
Remarque6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarter glass, Seat trunk seal to edge of trim
-
Position LH trunk side trim and install lower clips
Remarque1x push clips, 5x clips, Guide front clip stanchions around LH C-pillar
-
Connect 12V outlet and trunk switch connector and seat top edge of LH trunk side trim
Remarque6x clips, 2x connectors
-
Install LH trunk pocket bracket
Remarque1x push clip, 5x alignment tabs
-
Install LH load floor bracket
Remarque3x tabs, 2x clips
-
Install RH upper C-pillar trim
Remarque6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarterglass, Seat trunk seal to edge of trim
-
Install RH trunk side trim
Remarque1x push clip, 11x clips, Guide front clip stanchions around RH C-pillar
-
Install RH trunk pocket bracket
Remarque1x push clip, 5x alignment tabs
-
Install RH load floor bracket
Remarque3x tabs, 2x clips
-
Install trunk sill trim
Remarque4x clips, Seat seal around edge of trim
-
Install front load floor
-
Install rear load floor
-
Install the LH upper B-pillar assembly
Remarque4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim
-
Install LH rear sill trim
Remarque5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of LH rear sill trim into trunk side trim and work your way forward securing clips, Trim part may slightly differ, by vehicle build location
-
Reseat LH rear door seal
RemarqueSeat pillar and sill trim tabs underneath seal
-
Install the RH upper B-pillar assembly
Remarque4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim
-
Install RH rear sill trim
Remarque5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips
-
Reseat RH rear door seal
RemarqueSeat pillar and sill trim tabs underneath seal
-
Install 2nd row seat cushion
Remarque1x connector, Slide rear cushion rearward then align foam with seat rail, Make sure cushion is fully seated with push & pull test
- Close liftgate
- Move RH front seat to original position
-
Connect RH sun visor connector
Remarque1x connector
-
Install RH sun visor into headliner area
RemarqueFold sun visor to the closed and folded down position but do not latch in place
-
Install RH sun visor fastener
Remarque1x screw, T25, 3.5 Nm
-
Install RH sun visor bracket cover
Remarque4x clips
-
Install RH upper A-pillar trim
Remarque3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
-
Install RH mid A-pillar assembly
Remarque1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Make sure the seal seat on top of the trim
-
Install RH IP end cap
Remarque3x clips
- Move LH front seat to original position
-
Connect LH sunvisor connector
Remarque1x connector
-
Install LH sun visor into headliner area
RemarqueFold sun visor to the closed and folded down position but do not latch in place
-
Install LH sun visor fastener
Remarque1x screw, T25, 3.5 Nm
-
Install LH sun visor bracket cover
Remarque4x clips
-
Install LH upper A-pillar trim
Remarque3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
-
Install LH lower A-pillar trim
Remarque6x clips, 2 locating pins, Align front locating pin first
-
Install clip securing LH lower A-pillar trim
Remarque1x push clip
-
Install LH mid A-pillar assembly
Remarque1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
-
Install LH IP end cap
Remarque3x clips
- Connect to vehicle using Toolbox 3.0
- Select ‘Actions/Autodiag’ and search for ‘Service_Redeploy’
-
Select ‘UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
- Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
- Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
- Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
- Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
- Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
RemarqueSelect ‘X’ at top right of window to close once complete - Remove HSD or RJ45 cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
-
Once firmware redeploy is complete, Verify on center display release notes are present
RemarqueIf the redeploy fails you may receive an error message on UI
- Raise all four windows
-
Close all four doors
RemarqueIf 12V is powered up, Unlatch rear doors before closing