02/03/2023 06:55:21

Rail du siège – intérieur – siège de 2e rangée – gauche (7-places) (retirez et remplacez)

Code de correction 13020342 0.84 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Retirer

  1. Remove the LH 2nd row seat assembly from the vehicle. See Ensemble de siège - 2e rangée - gauche (7-places) (retirez et remplacez).
  2. Remove the push clip from the front of the LH 2nd row seat outer sideshield assembly.
    Conseil : Use a pick to remove the push clip from the bottom side of the outboard cover.
  3. Release the clip that attaches the LH 2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector, and then remove the sideshield from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  4. Release the clips (x3) that attach the LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from the seat assembly.
  5. Remove the LH 2nd row seat toe kick cover. See Couvercle - plaque de butée - siège de 2e rangée - gauche (7-places) (retirez et remplacez).
  6. Remove the LH 2nd row seat back panel. See Panneau arrière - siège de 2e rangée - gauche (retirez et remplacez).
  7. Remove the center 2nd row seat back panel. See Panneau arrière – siège de 2e rangée – 20/central (5 places) (retirez et remplacez).
  8. Disconnect the LH 2nd row seat harness electrical connectors (x7), and then release the clip that attaches the harness to the seat frame.
  9. Release the seat cables (x4) from the LH 2nd row seat EZ entry actuator.
  10. Remove the push clips (x2) from the LH 2nd row seat cushion pan.
  11. Remove the center 2nd row seat back pivot clamps. See Colliers à pivot - dossier de siège - 2e rangée - centre/20 (retirez et remplacez).
  12. Remove the center 2nd row lumbar bun. See Coussin lombaire - 2e rangée - centre/20 (retirez et remplacez).
  13. Lift the center 2nd row seat back upward to remove it from the seat assembly.
  14. Remove the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
    • Douille Torx T25
  15. Remove the LH 2nd row seat headrest trim. See Appuie-tête - 2e rangée - extérieur - gauche (retirez et remplacez).
  16. Remove the LH 2nd row headrest adjustment guide. See Guide de réglage - appuie-tête - 2e rangée (retirez et remplacez)
  17. Remove the LH 2nd row seat headrest guide lock. See Blocage du guide - appuie-tête - 2e rangée (retirez et remplacez).
  18. Release the clips (x4) that attach the LH 2nd row seat back to the seat assembly, and then lift the seat back to remove it from the assembly.
  19. Lift the rear of the LH 2nd row seat cushion assembly, and then slide the cushion toward the front of the seat to remove it from the seat assembly.
  20. Use a pick to manually move the LH 2nd row seat into easy entry position.
  21. Remove and discard the bolts (x2) that attach the LH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Douille de 11 mm
  22. With one hand, engage the towel bar, move the outer seat track rearward with the other hand until the groove on the LH seat podium releases from the outer seat track, and then lift the LH 2nd row seat podium upward while removing it from the inner seat track.
  23. Release the clips (x2) that attach the LH 2nd row EZ entry actuator cable to the RH easy entry latch, and then release the cable from the latch.
  24. Remove the nuts that attach the LH 2nd row seat inner seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Douille de 13 mm
  25. Remove the LH 2nd row seat inner seat track from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide the outer seat track outwards away from the towel bar.

Installer

  1. Position the LH 2nd row seat inner seat track into the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure the towel bar spring is in place and the bar is sitting between the tabs.
  2. Install the nuts that attach the LH 2nd row seat inner seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Install outer seat track to seat frame
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Douille de 13 mm
  3. Secure the clips (x2) that attach the LH 2nd row EZ entry actuator cable to the RH easy entry latch.
  4. Install the groove on the LH 2nd row seat podium to the inner seat track, and then align the groove on the podium to the outer seat track. Engage the towel bar with one hand, and then move the outer seat track inward until the groove on the podium engages to the seat track.
  5. Install new the bolts (x2) that attach the LH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Douille de 11 mm
  6. Position the LH 2nd row seat onto the seat tracks, and then push the seat downward to latch the floor latches.
  7. Starting at the rear of the seat, position the LH 2nd row seat pan onto the seat frame.
  8. Install the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The 10 mm bolts are torqued to 6 Nm. The T25 screws are torqued to 1.5 Nm.
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
    • Douille Torx T25
  9. Position the LH 2nd row seat back to the seat assembly, and then install the clips (x4) that attach the seat back to the assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure the bottom retainers slide into position.
  10. Install the LH 2nd row seat headrest guide lock. See Blocage du guide - appuie-tête - 2e rangée (retirez et remplacez).
  11. Install the LH 2nd row headrest adjustment guide. See Guide de réglage - appuie-tête - 2e rangée (retirez et remplacez)
  12. Install the LH 2nd row seat headrest trim. See Appuie-tête - 2e rangée - extérieur - gauche (retirez et remplacez).
  13. Install the center 2nd row seat back pivot clamps. See Colliers à pivot - dossier de siège - 2e rangée - centre/20 (retirez et remplacez).
  14. Install the center 2nd row lumbar bun. See Coussin lombaire - 2e rangée - centre/20 (retirez et remplacez).
  15. Position the LH 2nd row seat outer sideshield to the seat assembly, connect the electrical connector, and then secure the clip.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  16. Install the push clip to the front of the LH 2nd row seat outer sideshield assembly.
    Conseil : Use a pick to remove the push clip from the bottom side of the outboard cover.
  17. Install the clips (x3) that attach the LH 2nd row seat inboard outer trim to the LH 2nd row seat.
  18. Install the center 2nd row seat back panel. See Panneau arrière – siège de 2e rangée – 20/central (5 places) (retirez et remplacez).
  19. Install the LH 2nd row seat toe kick cover. See Couvercle - plaque de butée - siège de 2e rangée - gauche (7-places) (retirez et remplacez).
  20. Install the LH 2nd row seat back panel. See Panneau arrière - siège de 2e rangée - gauche (retirez et remplacez).
  21. Install the LH 2nd row seat assembly. See Ensemble de siège - 2e rangée - gauche (7-places) (retirez et remplacez).