Dossier de siège - 2e rangée - gauche (retirez et remplacez)
Code de correction
13054002 0.24 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.
- 2024-07-23: Deleted the seatback cushion separation steps.
- 2024-08-15: Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.
- Torchless Heat Induction Tool - 2152873-00-A
Caractéristiques techniques de couple
Description | Valeur de couple | Outils recommandés | Réutiliser/remplacer | Remarques |
---|---|---|---|---|
Bolts (x5) that attach the LH 2nd row seat back frame to the vehicle |
![]() 37 Nm (27.3 lbs-ft) |
|
Réutiliser |
ATTENTION Bolts must be installed in the following
sequence:
|
Retirer
- Remove the LH lower C-pillar trim. See Garniture - montant arrière - inférieure - gauche (retirez et remplacez).
- Release the clips (x3) that attach the main carpet to the lower seat cushion frames.
-
Remove the bolts (x5) that
attach the LH 2nd row seat back frame to the vehicle.
RemarqueThe two frontmost bolts are behind the main carpet.TIpNous recommandons l’utilisation des outils suivants :
- Douille de 11 mm
- Rallonge de 6 po
- Clé à rochet standard avec tête flexible 3/8 po
- Clé dynamométrique à tête flexible 3/8 po (installation seulement)
-
Carefully fold down the LH
2nd row seat back.
ATTENTIONPlace a protective covering on the seat back upholstery and take care not to damage the upholstery during removal of the seat back.ATTENTIONDo not place any additional weight on the seat back. Doing so may damage the seat frame alignment tabs, which can cause unevenness between the 60 and 40 seat backs.
- Disconnect the electrical harness from the connector at the LH lower seat frame.
-
With assistance, carefully
remove the LH 2nd row seat back assembly from the vehicle.
ATTENTIONPlace the seat back assembly in an area where it will not be tipped over or otherwise damaged.RemarqueFor NA only: If the 2nd row seat that is not being replaced does not have ISOFIX flag for child locks, replace the seat cover.. See Couvercle – dossier de siège – 2e rangée – gauche (5 places) (Retrait et remplacement).
Installer
- With assistance, position the LH 2nd row seatback assembly into place, and then connect the electrical harness to the connector at the LH lower seat frame.
- Move the LH 2nd row seatback to vertical position.
-
Install the bolts (x5) that attach the LH 2nd row seat back frame to the
vehicle.37 Nm (27.3 lbs-ft)NoteThe two frontmost bolts are behind the main carpet.NoteTorque in the sequence of:
- Front Outboard
- Rear Inboard
- Rear Outboard
- Front Inboard
TIpNous recommandons l’utilisation des outils suivants :- Douille de 11 mm
- Rallonge de 6 po
- Clé à rochet standard avec tête flexible 3/8 po
- Clé dynamométrique à tête flexible 3/8 po (installation seulement)
- Install the clips (x3) that attach the main carpet to the lower seat cushion frames.
- Install the LH lower C-pillar trim. See Garniture - montant arrière - inférieure - gauche (retirez et remplacez).