2024-01-02

Faisceau - filtre de climatiseur - batterie HT (Ensemble structural) (retirez et remplacez)

Code de correction 16305312 1.86 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Retirer

  1. Open all the doors and lower all the windows.
  2. Place the vehicle into Service Mode. See Mode Entretien.
  3. Remove the ancillary bay cover. See Couvercle - baie auxiliaire (Ensemble structural) (retirer et remplacer).
  4. Retirez le sectionneur de batterie pyrotechnique. Voir Sectionneur de batterie pyrotechnique (Ensemble structural) (retirez et installez).
  5. Release the locking tab, and then disconnect the AC filter harness connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Release the locking tab by pulling upward. Use a plastic trim tool to help lift the connector.
  6. Release the clips (x2) that attach the AC filter harness to the tray.
  7. Disconnect the fast charge contactor connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push on both side of connector to release the tabs, and then pull upward to disconnect.
  8. Remove and discard the bolt that attaches the AC filter harness to the negative DC inlet busbar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 13 mm
  9. Remove and discard the bolt that attaches the AC filter harness to the positive DC inlet busbar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 13 mm
  10. Remove the HV battery AC filter harness from the ancillary bay.

Installer

  1. Position the HV battery AC filter harness into the ancillary bay.
  2. Install a new bolt that attaches the AC filter harness to the positive DC inlet busbar.
    15 Nm (11.1 lbs-ft) -180 degrees
    5 Nm (3.7 lbs-ft) +60 degrees
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Tighten the bolt to 15 Nm, back off 180 degrees, then torque to 5 Nm +60 degrees.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 13 mm
  3. Install a new bolt that attaches the AC filter harness to the negative DC inlet busbar.
    15 Nm (11.1 lbs-ft) -180 degrees
    5 Nm (3.7 lbs-ft) +60 degrees
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Tighten the bolt to 15 Nm, back off 180 degrees, then torque to 5 Nm +60 degrees.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 13 mm
  4. Use a Hioki resistance meter to measure the resistance at the HV joint between the newly-installed AC filter harness and the positive DC inlet busbar.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The resistance should be 150µΩ or less.
  5. Use a Hioki resistance meter to measure the resistance at the HV joint between the newly-installed AC filter harness and the negative DC inlet busbar.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The resistance should be 150µΩ or less.
  6. Connect the fast charge contactor connector.
  7. Install the clips (x2) that attach the AC filter harness to the tray.
  8. Connect the PCS to fast charge contactor AC filter harness connector, and then engage the red locking tab.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure the connector is fully seated.
  9. Mesurez la tension à travers les points de montage de déconnexion de la batterie pyrotechnique puis installez la déconnexion de la batterie pyrotechnique Voir Sectionneur de batterie pyrotechnique (Ensemble structural) (retirez et installez).
  10. Install the ancillary bay cover. See Couvercle - baie auxiliaire (Ensemble structural) (retirer et remplacer).
  11. Exit Service Mode. See Mode Entretien.
  12. Remove the vehicle from the lift. See Soulever le véhicule - pont élévateur à 2 poteaux.
  13. Raise all the windows and close all the doors.