Tapis - avant - gauche (7-places) (retirez et remplacez)
Code de correction 15301152 0.72 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.
Retirer
- Open all the doors and lower all the windows.
- Move the LH front seat fully rearward.
-
Remove screw and clips (x2) that
attach the driver footwell cover to the instrument panel.Conseil : Nous recommandons l’utilisation des outils suivants :
- Douille Torx T20
-
Disconnect the connectors (x2), and
then release the tabs (x3) to remove the driver footwell cover from the vehicle.
- Remove the LH center console side panel carpet. See Panneau latéral - console centrale - gauche (retirez et remplacez).
-
Remove the bolts that attach the LH
front of the center console to the body.
RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
- Remove the LH mid A-Pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
- Remove the LH lower A-Pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
-
Release the LH front door seal from
the body.
- Release the clip that attaches the LH front carpet to the body near the front of the LH door opening.
- Fold the front of the LH front carpet rearward so that the LH body controller module and its surrounding connectors are exposed.
-
Remove and discard the bolts (x2) that
attach the front of the 1st row LH seat to the body.
ATTENTIONUse only the Torx Plus T45 bit to remove the seat bolts.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à rochet standard avec tête flexible 3/8 po
- Clé dynamométrique à tête flexible 3/8 po (installation seulement)
- Move the seat fully forward.
- Insérez la clé de libération de la ceinture de sécurité (1133787-00-A) dans le bas de l’accouplement du prétendeur de la ceinture de sécurité pour libérer la ceinture de sécurité du prétendeur.
-
Raise the LH front seat cushion to the
maximum height.
RemarqueAdjust the seat back if needed to avoid contacting the headliner.
- Remove the center console lower rear panel. See Panneau - arrière inférieur - console centrale (retirez et remplacez).
-
Remove the bolt that attaches the LH rear of the center console to the body.
RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
- Move the RH front seat fully forward.
-
Raise the RH front seat cushion to the maximum height.
RemarqueAdjust the seat back if needed to avoid contacting the headliner.
-
Remove the bolt that attaches the RH
rear of the center console to the body.
RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
- Move the RH front seat fully rearward and to the lowest position.
- Remove the RH center console side panel carpet. See Panneau latéral - console centrale - gauche (retirez et remplacez).
-
Remove the bolts that attach the RH
front of the center console to the body.
RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
-
Remove and discard the bolts (x2) that
attach the rear of the 1st row LH seat to the body.
ATTENTIONUse only the Torx Plus T45 bit to remove the seat bolts.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à rochet standard avec tête flexible 3/8 po
- Clé dynamométrique à tête flexible 3/8 po (installation seulement)
-
Adjust the LH front seat to the middle
of the seat tracks, and then raise the seat fully.
Conseil : Performing this step will aide in removing the seat.
- Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
- Remove the HEPA filter assembly. See Ensemble - filtre - HEPA (retirez et installez).
- Disconnect LV power. See Alimentation 12 V/BT (déconnectez et connectez).
- Locate the LH front seat electrical connector on the LH body controller module.
-
Release the LH front seat connector
lock, and then remove the connector from the LH body controller.
RemarqueSqueeze the release tab on the LH front seat connector lock, and then swing the lock away from the connector to release the lock.ATTENTIONDo not pull on the connector too hard. If the connector does not easily disconnect from the LH body controller, the lock is still engaged.
- Release the clips (x2) that attach the LH front seat harness to the LH footwell support bracket near the LH side of the LH footwell.
- Release the clips that attach the LH front seat harness to the LH front seat harness guide.
- Pull the LH front seat harness out from under the LH front carpet.
-
With assistance, remove the seat from
the vehicle.
RemarqueLift the seat, tilt the seat back, rotate the cushion toward the front door, and remove the seat from the vehicle, cushion first.ATTENTIONTake care not to damage the upholstery or trim while removing the seat.ATTENTIONIf reinstalling the seat, place the seat in an area where it is not likely to be tipped over or otherwise damaged.
- Disconnect the electrical connector from the rear of the center console.
- Disconnect the electrical connector that is located at the RH front of the center console.
-
With an assistant, remove the center
console from the vehicle as follows:
- Tilt the rear of the center console upwards.
- Pull the center console towards the rear of the vehicle.
- Tilt the front of the center console upwards.
- Remove the center console through the passenger front door.
-
Remove the clips (x2) that attach the
LH front carpet to the vehicle.
-
Lift up on the rear edge of the LH
front carpet, and then slide the carpet towards the rear of vehicle to remove it.
ATTENTIONBe careful to avoid the foam underneath the carpet catching on the seat risers.
Installer
-
Position the LH front carpet into the
vehicle.
-
Install the clips (x2) that attach the LH front carpet to the vehicle.
-
With an assistant, install the center
console into the vehicle as follows:
- Tilt the front of the center console downwards.
- Slide the center console towards the front of the vehicle.
- Tilt the rear of the center console downwards until it is in place.
-
Connect the electrical connector that
is located at the RH front of the center console.
ATTENTIONEnsure the connector is properly installed. Perform a push-pull test before continuing this procedure.
-
Install the bolts that attach the RH
front of the center console to the body.Install the bolts that attach the RH front of the center console to the body.Installez les boulons qui fixent la partie avant droite de la console centrale à la carrosserie.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
- Install the RH center console side panel carpet. See Panneau latéral - console centrale - gauche (retirez et remplacez).
-
Connect the electrical connector in
the rear of the center console.
ATTENTIONEnsure the connector is properly installed. Perform a push-pull test before continuing this procedure.
-
Install the bolt that attaches the LH
rear of the center console to the body.Install the bolt that attaches the LH rear of the center console to the body.Installez le boulon qui fixe la partie arrière gauche de la console centrale à la carrosserie.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
-
Install the bolts that attach the LH
front of the center console to the body.Install the bolts that attach the LH front of the center console to the body.Installez les boulons qui fixent la partie avant gauche de la console centrale à la carrosserie.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
- Install the LH center console side panel carpet. See Panneau latéral - console centrale - gauche (retirez et remplacez).
-
With assistance, position the 1st row
LH seat in the vehicle.
ATTENTIONTake care not to damage the upholstery or trim while positioning the seat.
- Route the 1st row LH seat harness under the LH front carpet, position the harness in the harness guide, and then install the clips that attach the harness to the harness guide.
- Install the clips (x2) that attach the LH front seat harness to the LH footwell support bracket near the LH side of the LH footwell.
-
Install the LH front seat harness
connector on the LH body controller, and then engage the connector lock.
RemarquePerform a push-pull test to ensure that the connector is fully seated and locked.
-
Fully seat the LH front carpet.
- Unfold the LH front carpet back into position, and then install the clip that attaches the carpet to the body near the front of the LH door opening.
- Install the LH lower A-Pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
- Install the LH mid A-Pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
-
Reseat the LH front door seal along
the lower A-pillar trim.
- Connect 12V/LV power. See Alimentation 12 V/BT (déconnectez et connectez).
- Install the HEPA filter assembly. See Ensemble - filtre - HEPA (retirez et installez).
- Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
- Move the LH front seat fully forward.
-
Install the LH 1st row seatbelt
retractor onto the pretensioner.
RemarqueAprès avoir réinstallé le prétendeur de la ceinture de sécurité dans l’accouplement du prétendeur, tirez sur les éléments pour vous assurer qu’ils sont bien installés.
-
Install the new bolts (x2) that attach
the rear of the 1st row LH seat to the body.Install the new bolts (x2) that attach the rear of the 1st row LH seat to the body.Installez les nouveaux boulons (x2) qui fixent l’arrière du siège gauche de première rangée à la carrosserie.ATTENTIONUse only the Torx Plus T45 bit to install the seat bolts.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à rochet standard avec tête flexible 3/8 po
- Clé dynamométrique à tête flexible 3/8 po (installation seulement)
- Move the RH front seat fully forward.
-
Raise the RH front seat cushion to the
maximum height.
RemarqueAdjust the seat back if needed to avoid contacting the headliner.
-
Install the bolt that attaches the RH
rear of the center console to the body.Install the bolt that attaches the RH rear of the center console to the body.Installez le boulon qui fixe la partie arrière droite de la console centrale à la carrosserie.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille de 10 mm
- Rallonge de 4 po
- Clé à cliquet standard ¼ po
- Clé dynamométrique ¼ po (installation seulement)
- Install the center console lower rear panel. See Panneau - arrière inférieur - console centrale (retirez et remplacez).
- Move the RH front seat to the original position.
- Move the LH front seat fully rearward.
-
Install the new bolts (x2) that attach
the front of the 1st row LH seat to the body.Install the new bolts (x2) that attach the front of the 1st row LH seat to the body.Installez les nouveaux boulons (x2) qui fixent l’avant du siège gauche de première rangée à la carrosserie.ATTENTIONUse only the Torx Plus T45 bit to install the seat bolts.RemarqueNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à rochet standard avec tête flexible 3/8 po
- Clé dynamométrique à tête flexible 3/8 po (installation seulement)
-
Position the driver footwell cover
into the vehicle, and then connect the connectors (x2) and then secure the tabs
(x3).
-
Install screw and clips (x2) that
attach the driver footwell cover to the instrument panel.RemarqueT20Conseil : Nous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Move the LH front seat to the original position.
- Raise all the windows and close all the doors.