2026-11-03

Interrupteur - volant - gauche (retirez et remplacez)

Code de correction 17300702 0.30 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps à taux fixe (FRT) connexe représentent tout le travail à accomplir pour cette procédure, y compris les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

  • 2026-11-03: Updated the specification of the bolts (x4) that attach the bright surround to the steering wheel.

Retirer

  1. Remove the driver airbag. See Coussin gonflable - conducteur (retirez et remplacez).
  2. Disconnect the steering wheel electrical wiring harness from the connector.
  3. Disconnect the electrical harness from the LH steering wheel switch connector.
  4. Disconnect the electrical harness from the RH steering wheel switch connector.
  5. Release the clips that attach the horn assembly, and then move the horn assembly to the side.
  6. Disconnect the electrical harness from the lower connector, and then remove the electrical harness from the steering wheel.
  7. Remove the screws (x4) that attach the bright surround to the steering wheel, and then remove the surround.
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Pry the lower portion of the bright surround assembly away from the steering wheel, and then work your way around. Do not remove it now. Wait until the steering wheel is removed.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  8. Remove the screws (x3) that attach the LH steering wheel switch to the bright surround, and then remove the switch from the surround.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit

Installer

  1. Install the LH steering wheel switch into the bright surround, and then install the screws (x3) that attach the switch to the surround.
    0.9 Nm (8 lbs-in)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  2. Install the bright surround into the steering wheel, and then install the screws (x4) that attach the surround to the steering wheel.
    2.5 Nm (1.8 lbs-ft)
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Torque the T25 bolts to 2.5 Nm; torque the PH1 bolts to 1.8 Nm.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  3. Install the electrical harness into the steering wheel, and then connect the electrical harness to the lower connector.
  4. Move the horn assembly to the center, and then fasten the clips that attach the horn assembly.
  5. Connect the electrical harness to the RH steering wheel switch connector.
  6. Connect the electrical harness to the LH steering wheel switch connector.
  7. Connect the steering wheel electrical harness to the connector.
  8. Install the driver airbag. See Coussin gonflable - conducteur (retirez et remplacez).