2023-03-02

Tapis - avant - gauche (Ensemble structural) (retirez et remplacez)

Code de correction 15301132 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Retirer

  1. Remove the LH mid A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
  2. Remove the LH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
  3. Remove the LH center console side panel. See Panneau latéral - console centrale - gauche (retirez et remplacez).
  4. Remove screw and clips (x2) that attach the driver footwell cover to the instrument panel.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
  5. Disconnect the connectors (x2), and then release the tabs (x3) to remove the driver footwell cover from the vehicle.
  6. Move the LH front seat fully forward.
  7. Remove and discard the bolts (x2) that attach the rear of the 1st row LH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à rochet standard avec tête flexible 3/8 po
    • 3/8 in flex head torque wrench (installation only)
  8. Move the seat fully rearward.
  9. Remove and discard the bolts (x2) that attach the front of the 1st row LH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à rochet standard avec tête flexible 3/8 po
    • 3/8 in flex head torque wrench (installation only)
  10. Position the LH front seat up and carefully lean it backwards.
  11. Release the push clips (x2) and vertical clip that attach the LH front carpet to the cabin support.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Insert a clip pry tool on the outboard side of the clip, and then rotate to the right to release one side of clip. Move the clip pry tool inboard of clip and rotate to left to fully release the carpet clip from cabin support.
  12. Release the clips (x4) that attach the LH front carpet underneath the seat.
    Figure 1. Seat removed for clarity
  13. Release the harness clip and harness, release all edges, and then remove the LH front carpet from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Take note of the short edge under the center console.

Installer

  1. Position the LH front carpet into the vehicle, and then secure the harness clip and harness and all edges.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Tuck the short edge underneath the center console.
  2. Install the clips (x4) that attach the LH front carpet underneath the seat.
    Figure 2. Seat removed for clarity
  3. Install the vertical clip and push clips (x2) that attach the LH front carpet to the cabin support.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Secure the vertical clip into place first.
  4. Position the LH front seat down and carefully tilt it forwards.
  5. Install the new bolts (x2) that attach the front of the 1st row LH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Install the new bolts (x2) that attach the front of the 1st row LH seat to the body.Installez les nouveaux boulons (x2) qui fixent l’avant du siège gauche de première rangée à la carrosserie.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à rochet standard avec tête flexible 3/8 po
    • 3/8 in flex head torque wrench (installation only)
  6. Move the LH front seat fully forward.
  7. Install the new bolts (x2) that attach the rear of the 1st row LH seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Install the new bolts (x2) that attach the rear of the 1st row LH seat to the body.Installez les nouveaux boulons (x2) qui fixent l’arrière du siège gauche de première rangée à la carrosserie.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx Plus T45
    • Clé à rochet standard avec tête flexible 3/8 po
    • 3/8 in flex head torque wrench (installation only)
  8. Move the LH front seat to the original position.
  9. Position the driver footwell cover into the vehicle, and then connect the connectors (x2) and then secure the tabs (x3).
  10. Install screw and clips (x2) that attach the driver footwell cover to the instrument panel.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
  11. Install the LH center console side panel. See Panneau latéral - console centrale - gauche (retirez et remplacez).
  12. Install the LH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
  13. Install the LH mid A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
  14. Close the LH front door.