Commande de la direction (retirez et remplacez)
Code de correction
17154802 0.24
REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps à taux fixe (FRT) connexe représentent tout le travail à accomplir pour cette procédure, y compris les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.
REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création.
REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.
- 2026-11-03: Updated the specification of the screws (x4) that attach the bright surround to the steering wheel.
Spécifications de couple
| Description | Valeur de couple | Outils recommandés | Réutiliser/remplacer | Remarques |
|---|---|---|---|---|
| Screws (x4) that attach the bright surround to the steering wheel, and then remove the surround |
![]() 2.5 Nm (1.8 lbs-ft) ![]() 1.8 Nm (1.3 lbs-ft) |
|
Réutiliser |
T25 bolts: 2.5 Nm PH1 bolts: 1.8 Nm |
| Screws (x2) that attach the steering wheel controls ECU to the bright surround |
![]() 0.9 Nm (8 lbs-in) |
|
Réutiliser |
Retirer
- Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
- Disconnect 12V power. See Alimentation 12 V/BT (déconnectez et connectez).
- Remove the driver airbag. See Coussin gonflable - conducteur (retirez et remplacez).
-
Disconnect the steering wheel electrical wiring harness from the connector.
-
Release the clips that attach the horn assembly, and then move the horn assembly to the side.
-
Remove the screws (x4) that attach the bright surround to the steering wheel, and then remove the surround.
NoteDepending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.NotePry the lower portion of the bright surround assembly away from the steering wheel, and then work your way around. Do not remove it now. Wait until the steering wheel is removed.TipUse of the following tool(s) is recommended:
- Torx T25 bit
- PH1 Stubby Phillips Screwdriver
-
Disconnect the electrical harness from the steering wheel controls ECU connector.
-
Remove the screws (x2) that attach the steering wheel controls ECU to the bright surround, and then remove the ECU from the surround.
TipL'un ou plusieurs des outils suivants sont recommandés :
- T10 Torx bit
Installer
-
Install the steering wheel controls ECU into the bright surround, and then install the screws (x2) that attach the ECU to the surround.
0.9 Nm (8 lbs-in)TipL'un ou plusieurs des outils suivants sont recommandés :- T10 Torx bit
-
Connect the electrical harness to the steering wheel controls ECU connector.
-
Install the bright surround into the
steering wheel, and then install the screws (x4) that attach the surround to the
steering wheel.
2.5 Nm (1.8 lbs-ft)
1.8 Nm (1.3 lbs-ft)NoteDepending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.NoteTorque the T25 bolts to 2.5 Nm; torque the PH1 bolts to 1.8 Nm.TipUse of the following tool(s) is recommended:- Torx T25 bit
- PH1 Stubby Phillips Screwdriver
-
Move the horn assembly to the center, and then fasten the clips that attach the horn assembly.
-
Connect the steering wheel electrical harness to the connector.
- Install the driver airbag. See Coussin gonflable - conducteur (retirez et remplacez).
- Connect 12v power. See Alimentation 12 V/BT (déconnectez et connectez).
- Réinstaller le micrologiciel du véhicule. Voir Réinstallation du logiciel – Écran tactile,
- Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).