2024-10-17
Moteur – rail de siège – siège passager avant (retrait et remplacement)
Code de correction
13013202 0.42 NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when
performing the below procedure.
- 2024-10-15: Updated post-installation routines.
- 2023-12-08: Re-write the whole procedure according to the latest validation.
Description | Valeur de couple | Outils recommandés | Réutiliser/remplacer | Remarques |
---|---|---|---|---|
Front passenger seat fasteners (x4) |
![]() 33.5 Nm (24.7 lbs-ft) |
|
Remplacer | Bolts are patched |
Bolt that attaches the lift motor assembly to the rear RH link |
![]() 18 Nm (13.3 lbs-ft) |
|
Remplacer | Bolts are patched |
Bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly |
![]() 23 Nm (17.0 lbs-ft) |
|
Réutiliser | Bolts are patched |
Avertissement
Seat base edges are
sharp and can cause personal injury. Wear cut resistant gloves when removing the seat
from the vehicle, and while performing procedures that involve work on or near the seat
base.
Retirer
- Open all doors and lower all windows.
- Remove the RH instrument panel end cap. See Capuchons d’extrémité - tableau de bord - gauche (retirez et remplacez).
- Remove the RH middle A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
- Release the bottom half of the RH front door seal.
- Remove the RH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
- Use a clip prytool to release the RH front seat harness from the lower A-pillar 12V bracket clips (x5).
- Pull the RH front seat harness from under the RH front cabin carpet.
-
Move the RH front seat forward, and then remove and discard the RH front seat rear fasteners (x2).
TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à cliquet sans fil/Visseuse à percussion
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
- Raise the RH front seat cushion to maximum height for access to the HV battery bolts at the RH front footwell and below the RH front seat.
-
Move the RH front seat backward, and then remove and discard the RH front seat front fasteners (x2).
TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à cliquet sans fil/Visseuse à percussion
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
-
Tilt the seat backward to gain access to the underside of the LH front seat.
RemarqueTake care when moving the seat. Ensure the carpet is not damaged.
-
Remove and discard the bolt that attaches the lift motor assembly to the rear RH link.
TIpNous recommandons l’utilisation des outils suivants :
- Torx Bit T45 Stubby
- Clé à cliquet/Clé dynamométrique
- Rallonge de 3 po
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
- Clé à cliquet sans fil/Visseuse à percussion
-
With assistance, remove the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.
TIpNous recommandons l’utilisation des outils suivants :
- Torx T50 Bit Stubby
- Rallonge de 3 po
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
- Clé à cliquet sans fil/Visseuse à percussion
- Disconnect the front passenger seat track motor electrical connector.
- Use a clip prytool to remove the harness clips (x2) from the RH front seat track motor.
-
Release the front passenger seat outer track from the track bridge assembly.
RemarquePry up on the bridge tack motor tab, and then slide the outer track away to release it.
-
Release the RH front seat track bridge assembly from the inner seat track.
RemarquePry up on the bridge tack motor tab, and then slide the seat track bridge assembly away to release it.
Installer
-
Install the RH front seat outer track onto the track bridge assembly.
RemarqueThe track motor cable is keyed square and must be aligned with the inner track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
-
Install the track motor bridge to the inner track.
RemarqueThe track motor cable is keyed square and must be aligned with the inboard track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
- Connect the track motor electrical connector.
- Install the harness clips (x2) to the RH front seat track motor.
-
With assistance, install the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.23 Nm (17.0 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Torx T50 Bit Stubby
- Rallonge de 3 po
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
- Clé à cliquet sans fil/Visseuse à percussion
-
Install a new bolt that attaches the lift motor assembly to the rear RH link.18 Nm (13.3 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Torx Bit T45 Stubby
- Clé à cliquet/Clé dynamométrique
- Rallonge de 3 po
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
- Clé à cliquet sans fil/Visseuse à percussion
-
Reposition the RH front seat onto the RH front seat risers.
RemarqueTake care when moving the seat. Ensure the carpet is not damaged.
- Secure the RH front seat harness under the RH front cabin carpet.
- Install the RH front seat harness to the lower A-pillar 12V bracket clips (x5).
-
Move the RH front seat forward, and then install new RH front seat rear fasteners (x2).33.5 Nm (24.7 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à cliquet sans fil/Visseuse à percussion
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
-
Move the RH front seat backward, and then install new RH front seat front fasteners (x2).33.5 Nm (24.7 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx Plus T45
- Clé à cliquet sans fil/Visseuse à percussion
- Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
- Install the RH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
- Install the RH middle A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
- Install the RH instrument panel end cap. See Capuchons d’extrémité - tableau de bord - gauche (retirez et remplacez).
- Install the RH front door seal along the lower A-pillar trim.
- Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3.0 (connecter et déconnecter).
-
For NA vehicles only: On the
laptop, select the Actions tab, then search for "OCS". Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration
routine.
RemarqueVerify the seat is clear from any tooling or objects prior to calibration.
- On the laptop, select the Actions tab, then search for "Seat calibration". Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link) routine.
- Disconnect Toolbox and remove the laptop from the vehicle.
- Disable Service Mode. See Mode Entretien.
- Move the RH front seat to original position.
- Raise all windows and close all doors.