08/11/2024 00:31:01

Pompe - liquide de refroidissement - batterie - Super-collecteur (retirez et remplacez)

Code de correction 18401802 0.96 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Informational PurposesAn informational icon, calling your attention
Remarque
If the coolant pump has been replaced twice, escalate a Toolbox session before proceed.
  1. Log into Tesla Garage
  2. Enter vehicle VIN and select "Search"
  3. Check Firmware version
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Firmware package installed must be 2021.36 or above for vehicle configuration update and Toolbox routine
  4. Navigate to "CFG" tab on "Vitals" page
  5. Check the coolant pump GTW configuration, and make sure the configuration is set to DUAL_MIX.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    The Coolant Pump Identification will depend on this new configuration.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If the configuration is set to DUAL or DUAL_SAN_P4, change the configuration to DUAL_MIX. If the gateway configuration is already set to DUAL_MIX, no further configuration is required.
  6. Open LH front door
  7. Lower LH front window
  8. Connect to vehicle using Toolbox 3.0
  9. Select "Dashboards" tab, and select "Infotainment Dashboard"
  10. Select "Vehicle Configuration"
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Configuration values should load automatically, if not select "Read Config" and "Run" to load
  11. Select "Read Config" and select "Run" to pull current vehicle configuration, Verify configuration change was performed
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Read config and verify configuration change was successful, Refresh page if required, Select ‘X’ at top right of window to close once complete
  12. Scroll down to "coolantPumpType" and change to "Two coolant pumps installed, mixed pole pair batches"
  13. Select "Apply Changes" and select "Run" to save updated configuration
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Center display will reboot, Toolbox connection will be lost, Select ‘X’ at top right of window to close once complete
  14. Select ‘Actions/Autodiag’ and search for ‘Thermal’
  15. Select "Start Thermal Fluid Fill/Drain (Coolant only)", click Run and allow routine to complete
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once complete, Verify vehicle is in Series via Garage > Vitals > Thermal tab > Coolant loops, Thermal Fluid Fill/Drain routine has a 5 hour limit, After 5 hours routine must be performed again
  16. Vehicle preparation
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure vehicle is not charging before the repair
  17. Open hood
  18. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips
  19. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via Controls > Safety & Security > Vehicle Power > Power Off
  20. Disconnect 12V negative terminal and first responders loop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x nut, 10mm, 6 Nm, 1x connector, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V, Negative terminal should be disconnected before FRL, Allow 2 minutes for all electrical circuits to fully discharge
  21. Remove fresh air intake duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 4 Nm, 2x clips, 1x pin, Remove bolt, Gently pry pin out from thermal beam, then remove from bulkhead studs
  22. Disconnect powertrain coolant pump connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking electrical connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector
  23. Disconnect battery coolant pump connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking electrical connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector
  24. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  25. Remove outer fasteners from front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x bolts, 10mm, 5 Nm
  26. Remove remaining nuts and remove front aero shield from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 15mm, 5 Nm
  27. Position coolant drain container underneath battery coolant pump
  28. Remove bolts securing battery coolant pump to Supermanifold
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, T20, 1.8 Nm
  29. Remove battery coolant pump from Supermanifold
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure both o-rings (inner purple, and outer black) come off with old pump
  30. Position battery coolant pump to Supermanifold and install bolts hand tight
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, T20, 1.8 Nm, Lubricate both o-rings with silicone o-ring lubricant, Refer to connector position and install coolant pump with connector tab facing up, Recommend installing upper right bolt with coolant pump for easier installation, Make sure the coolant pump is fully seated
  31. Remove coolant drain container from underneath vehicle
  32. Position the front aero shield to vehicle and install nuts
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 15mm, 5 Nm
  33. Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x bolts, 10mm, 5 Nm
  34. Lower vehicle until tires are touching the ground
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  35. Torque bolts securing battery coolant pump to supermanifold
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, T20, 1.8 Nm
  36. Connect battery coolant pump connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking electrical connector, Engage locking tab
  37. Connect powertrain coolant pump connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x locking electrical connector, Engage locking tab
  38. Remove coolant bottle cap
  39. Place empty coolant container into front storage area
  40. Fill container with at least 15L of coolant
  41. Place filled coolant container into front storage area
  42. Setup vacuum refill tool
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify all valves on refill tool are in the closed position, See image for clarity
  43. Install vacuum refill cap onto coolant bottle assembly
  44. Setup vacuum refill tool
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify all valves on refill tool are in the closed position, See image for clarity
  45. Install vacuum refill hose into refill cap on coolant bottle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Perform push-pull-push test to verify hose is fully installed
  46. Position overflow hose into empty container
  47. Connect shop air supply to coolant refill tool
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If not already done, Verify refill valve is set to off
  48. Open air inlet valve to draw a vacuum, Once gauge stabilizes, Fully close valve
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Gauge stabilizes roughly (60-70 cmHg), Vacuum should not drop after the valves are closed
  49. Slowly open the refill valve to allow coolant to be drawn into the system
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure hose end of refill hose is fully submerged during entire process
  50. Once the gauge reads zero, close the refill valve
  51. Once the gauge reads zero, close the refill valve
  52. Once the gauge reads zero, close the refill valve
  53. Once the gauge reads zero, close the refill valve
  54. Disconnect shop air supply from coolant refill tool
  55. Remove coolant refill hose from coolant container
  56. Remove coolant overflow hose from coolant container
  57. Remove vacuum refill hose from refill cap on coolant bottle
  58. Remove coolant refill tool from vehicle
  59. Remove both coolant containers from inside underhood area
  60. Connect first responder loop and 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x nut, 10mm, 6 Nm, 1x connector, Engage locking tab, Connect FRL first before connecting 12V to avoid damage to car computer
  61. Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAINvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once complete
  62. Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete
  63. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure that the fluid level is at the Max line
  64. Install coolant bottle cap
  65. Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : TEST-SELF_VCFRONT_X_COOLANT-PUMPS-IDENTIFICATIONvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Run Coolant Pumps Identification
    • Thermal ➜ Coolant System ➜ Pump Identification
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once complete, Ensure VCFRONT_a490_coolantPumpsNotIdentified has cleared
  66. Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once complete.
  67. Install fresh air intake duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm bolt, 4 Nm, 2x clips, 1x pin, Set clips on bulkhead studs, Secure to thermal bar
  68. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
  69. Close hood
  70. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lower rack arms fully and remove from under vehicle if necessary, Remove air suspension from "Jack Mode" if equipped