2023-04-26

Brightwork - Center Console (2.0) (Remove and Replace)

Correction code 15190252 0.25 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 전면 도어를 열고 전면 창문을 내립니다.
  2. 전면 시트를 가장 낮고 가장 뒤쪽의 위치로 옮깁니다.
  3. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  4. 12V/LV 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  5. 센터콘솔 암레스트를 완전히 엽니다.
  6. 센터콘솔 장식 트림을 센터콘솔에 고정하는 클립(17개)을 분리한 다음 커넥터를 연결 해제하고 센터콘솔에서 장식 트림을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    먼저 주변 클립을 분리한 다음 트림의 전면 상단부를 분리합니다.
  7. 브라이트워크를 센터콘솔에 고정하는 나사(14개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  8. 플라스틱 트림 도구를 사용해 브라이트워크를 센터콘솔에 고정하는 위치 지정 탭(12개)을 분리합니다.

Install

  1. 브라이트워크를 센터콘솔에 고정하는 위치 지정 탭(12개)을 조입니다.
  2. 브라이트워크를 센터콘솔에 고정하는 나사(14개)를 장착합니다.
    1.6 Nm (1.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 육각 토크 렌치(장착 전용)
  3. 센터콘솔 장식 트림 어셈블리를 센터콘솔에 배치하고 커넥터를 연결한 다음 장식 트림을 센터콘솔에 고정하는 클립(17개)을 조입니다.
  4. 센터콘솔 암레스트를 닫습니다.
  5. 12V/LV 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  6. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  7. 전면 시트 등받이를 원래 위치로 이동합니다.
  8. 전면 창문을 올리고 전면 도어를 닫습니다.