18/05/2023 19:55:23

커버 - 시트 등받이 - 2열 - RH(7인승)(탈거 및 교체)

교정 코드 13081022 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

탈거

  1. Open the RH front and both rear doors.
  2. Lower the RH front and both rear windows.
  3. Move the RH 2nd row seat forward using the towel bar.
  4. Remove the RH 2nd row back panel. See 후면 패널 - 2열 시트 - RH(탈거 및 교체).
  5. Remove the RH 2nd row seat should switch. See 숄더 스위치 - 등받이 - 2열 - LH(탈거 및 교체).
  6. Remove the RH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - RH(7인승)(탈거 및 교체).
  7. Remove the clips (x2) and elastic harness holder that attach the seat harness to the bottom side of the seat frame, and then disconnect the 2nd row seat connector.
  8. Remove the RH 2nd row headrest. See 헤드레스트 - 2열 - 외측 - LH(탈거 및 교체).
  9. Remove the RH 2nd row headrest adjustment guide and guide lock. See:
  10. Release the clips (x4) that attach the RH 2nd row seat back assembly to the vehicle, and then lift the seat back upward to remove it from the vehicle.
  11. Place the RH 2nd row seat back assembly on a suitable working surface.
  12. Disconnect the seat heating connector.
  13. Release the tabs (x16) that attach the RH 2nd row seat back cover to the seat back assembly.
  14. Remove the back rest shell from the RH 2nd row seat back cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    Early production vehicles may have staples holding the material to the shell in some areas.
  15. Release the hook and loop attachment around the perimeter, cut and discard the hog rings (x3), and then remove the RH 2nd row seat back cover from the foam.
    Informational PurposesAn informational icon, calling your attention
    참고
    Clean any remaining debris from the assembly.

장착

  1. Position the RH 2nd row seat back cover onto the foam, and then install the hog rings (x3) and secure the hook and loop around the perimeter.
    Informational PurposesAn informational icon, calling your attention
    참고
    Small cable ties may be used as a substitute for the hog rings. If cable ties are used, trim the excess cable flush, and then rotate the head away from the visible areas.
  2. Position the seat back shell into the RH 2nd row seat back cover, and then secure the tabs (x16) that attach the cover to the seat back shell.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the cover is evenly distributed on the front of the back rest.
  3. Connect the seat heating connector.
  4. Position the RH 2nd row seat back cover into the vehicle, and then install the seat back assembly into the seat assembly.
  5. Install the RH 2nd row headrest adjustment guide and guide lock. See:
  6. Install the RH 2nd row headrest. See 헤드레스트 - 2열 - 외측 - LH(탈거 및 교체).
  7. Connect the 2nd row seat harness connector, and then secure the clips (x2) and elastic harness holder that attach the seat harness to the bottom side of the seat frame.
  8. Install the RH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - RH(7인승)(탈거 및 교체).
  9. Install the RH 2nd row seat should switch. See 숄더 스위치 - 등받이 - 2열 - LH(탈거 및 교체).
  10. Install the RH 2nd row back panel. See 후면 패널 - 2열 시트 - RH(탈거 및 교체).
  11. Move the RH 2nd row seat back to the vertical position.
  12. Move the front passenger seat to the original position.
  13. Raise the RH front and rear windows.
  14. Close the RH front and rear doors