교정 코드 33251022 0.66 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

1. Open the LH front door and lower the LH front window
2. Move LH front seat backward
3. Open hood
4. Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
5. Remove bolt securing frunk to washer fluid reservoir neck
   참고

   1x bolt, 10mm, 5 Nm

   

6. Release washer tank neck from washer tank and set aside
   참고

   1x O-ring, No need to remove hose from neck

   

   

7. Remove HEPA filter assembly
   참고

   2x bolts, 10mm, 5 Nm, Pivot rearward edge up and past brake reservoir, then lift up to clear frunk assembly

   

   

   

8. Power off vehicle from center display
   참고

   Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
9. Disconnect LV battery connector and First Responder Loop
   참고

   2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

   

   

   

10. Remove LH front floormat
11. Remove LH console side panel carpet
    참고

    11x clips, 2x guide pins, Use trim tool starting at top edge to release upper clips, then pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged

    

    

12. Remove the driver knee airbag. See 에어백 - 무릎 - 운전석(탈거 및 장착)
13. Remove the LH footwell air duct

    

    

14. Disconnect brake switch
    참고

    1x connector

    

15. Remove brake switch from pedal assembly
    참고

    Twist counter clockwise 45 degrees to remove. Replace if damaged during removal

    

16. Remove cotter clip from clevis pin on brake pedal assembly
    참고

    1x clip

    

17. Remove clevis pin from brake pedal assembly
    참고

    1x pin

    

    

    

18. Disconnect accelerator pedal connector
    참고

    1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector

    

19. Remove clip securing pedal harness to pedal assembly
    참고

    1x clip

    

20. Remove inner nuts securing pedal assembly to superdash
    참고

    2x nuts, 13mm, 16.5 Nm, Discard nyloc nuts after removal

    

21. Remove outer nuts securing pedal assembly to superdash
    참고

    3x nuts, 13mm, 16.5 Nm, Located under cowl, Discard nyloc nuts after removal

    

    

    

    

22. Remove pedal assembly
    참고

    2x studs, Release from iBooster studs then negotiate around iBooster rod

    

    

    

23. Position pedal assembly
    참고

    2x studs, Negotiate around iBooster rod then secure onto iBooster studs

    

    

    

24. Install outer nuts securing pedal assembly to superdash
    참고

    3x nuts, 13mm, 16.5 Nm, Located under cowl, Install new nyloc nuts

    

    

    

    

25. Install inner nuts securing pedal assembly to superdash
    참고

    2x nuts, 13mm, 16.5 Nm, Install new nyloc nuts

    

26. Install clip securing pedal harness to pedal assembly
    참고

    1x clip

    

27. Connect accelerator pedal connector
    참고

    1x connector, Engage locking tab

    

28. Align brake pedal to iBooster rod and install clevis pin to brake pedal assembly
    참고

    1x pin

    

    

    

29. Install cotter pin into clevis pin clip on brake pedal assembly
    참고

    1x clip

    

30. Install new brake switch clip into the new pedal assembly
    참고

    1x clip

    

31. Install brake switch onto pedal assembly
    참고

    Confirm that the brake pedal is in the home position, iBooster and Brake Pedal must be assembled together for brake light switch to be installed, Push the brake switch into the clip until it stops (don't push so hard as to move the brake pedal), Twist clockwise 45 degrees to set the brake switch, Make sure brake switch connector facing RH side of vehicle with connector pins vertical

    

32. Connect brake switch connector
    참고

    1x connector

    

33. Install the LH footwell duct into HVAC module

    

34. Connect the driver knee air bag and install into vehicle
    참고

    1x connector, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector

    

    

35. Install fasteners securing driver knee air bag to vehicle
    참고

    4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 2x push clips

    

    

    

    

36. Install connectors to LH footwell cover and position for installation
    참고

    3x tabs, 1x Ethernet connector, 1x puddle light connector

    

    

    

37. Install screw and clips securing LH footwell cover
    참고

    1x screw, T20, 2.5 Nm, 2x push clips

    

38. Install LH console side panel carpet
    참고

    11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install

    

    

    

    

39. Install LH front floormat
40. Connect first responder loop and LV battery
    참고

    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

41. Install HEPA filter assembly
    참고

    2x bolts, 10mm, 5 Nm, Pivot forward edge down past frunk assembly, then carefully move rear edge past brake reservoir and into position

    

    

    

42. Install washer tank neck to washer tank
    참고

    1x O-ring, Ensure washer hose is properly routed after installation

    

43. Secure frunk to washer fluid reservoir neck
    참고

    1x bolt, 10mm, 5 Nm

    

44. Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
45. Close hood
46. Move LH front seat to original position
47. Raise LH front window
48. Close LH front door