2026-08-27

Tie Rod - Inner - LH (Remove and Replace)

교정 코드 32013202 32013302 FRT 0.48 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  • 2025-12-16: Released new procedure.

탈거

  1. Remove the LH front wheel arch liner. See 휠 아치 라이너 - 전면 - LH(구조용 팩 이외)(탈거 및 교체) or 휠 아치 라이너 - 전면 - LH(구조용 팩)(탈거 및 교체).
  2. Remove LH outer tie rod from knuckle
    참고
    1x nyloc nut, 22mm, 180 Nm, Discard after removal
  3. Remove LH tie rod end from knuckle
  4. Remove large bellows clamp from bellows
    참고
    1x clamp, Discard after removal
  5. Remove bellows seal clip from bellows
    참고
    1x clip
  6. Slide bellows toward LH outer tie rod end
    참고
    You need to access the LH inner tie rod end inner ball joint
  7. Remove LH tie rod assembly from pinion housing
    참고
    1x inner tie rod, 38mm crowfoot, 88 Nm, Twist until it comes off

장착

  1. Adjusting new tie rod length to match old tie rod before installation
    참고
    1x jam nut, 21mm, 14mm, Turn adjust inner tie rod as needed, Parts line up is to count the threads on the removed tie rod then adjust to the same count on the new one, This will make alignment adjustment easier
  2. Install LH inner tie rod assembly onto pinion housing
    참고
    1x inner tie rod, 38 crowfoot, 88 Nm, Twist until it's fully seated
  3. Slide bellows into clamping position
    참고
    Slide bellows over pinion housing in preparation for clamping
  4. Secure large bellows clamp onto bellows
    참고
    1x clamp
  5. Secure bellows seal clip onto bellows
    참고
    1x clamp
  6. Position LH tie rod end to LH front knuckle
  7. Install nut securing the LH tie rod end to the knuckle
    참고
    1x nyloc nut, 22mm, 180 Nm, Install new nyloc nut
  8. Install the LH front wheel arch liner. See 휠 아치 라이너 - 전면 - LH(구조용 팩 이외)(탈거 및 교체) or 휠 아치 라이너 - 전면 - LH(구조용 팩)(탈거 및 교체).
  9. Review wheel alignment requirements and add correction code as needed. See 얼라인먼트 요구 사항 - 서스펜션.