28/02/2023 18:44:36

시트 트랙 - 내측 - 2열 시트 - LH(7인승)(탈거 및 교체)

교정 코드 13020342 0.84 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

탈거

  1. Remove the LH 2nd row seat assembly from the vehicle. See 시트 어셈블리 - 2열 - LH(7인승)(탈거 및 교체).
  2. Remove the push clip from the front of the LH 2nd row seat outer sideshield assembly.
    팁: Use a pick to remove the push clip from the bottom side of the outboard cover.
  3. Release the clip that attaches the LH 2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector, and then remove the sideshield from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  4. Release the clips (x3) that attach the LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from the seat assembly.
  5. Remove the LH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - LH(7인승)(탈거 및 교체).
  6. Remove the LH 2nd row seat back panel. See 후면 패널 - 2열 시트 - LH(탈거 및 교체).
  7. Remove the center 2nd row seat back panel. See 후면 패널 – 2열 시트 – 중앙/20(5인승)(탈거 및 교체).
  8. Disconnect the LH 2nd row seat harness electrical connectors (x7), and then release the clip that attaches the harness to the seat frame.
  9. Release the seat cables (x4) from the LH 2nd row seat EZ entry actuator.
  10. Remove the push clips (x2) from the LH 2nd row seat cushion pan.
  11. Remove the center 2nd row seat back pivot clamps. See 피벗 클램프 - 시트 등받이 - 2열 - 중앙/20(탈거 및 교체).
  12. Remove the center 2nd row lumbar bun. See 럼버번 - 2열 - 중앙/20(탈거 및 교체).
  13. Lift the center 2nd row seat back upward to remove it from the seat assembly.
  14. Remove the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • Torx T25 소켓
  15. Remove the LH 2nd row seat headrest trim. See 헤드레스트 - 2열 - 외측 - LH(탈거 및 교체).
  16. Remove the LH 2nd row headrest adjustment guide. See 조정 가이드 - 헤드레스트 - 2열(탈거 및 교체)
  17. Remove the LH 2nd row seat headrest guide lock. See 가이드 잠금 장치 - 헤드레스트 - 2열(탈거 및 교체).
  18. Release the clips (x4) that attach the LH 2nd row seat back to the seat assembly, and then lift the seat back to remove it from the assembly.
  19. Lift the rear of the LH 2nd row seat cushion assembly, and then slide the cushion toward the front of the seat to remove it from the seat assembly.
  20. Use a pick to manually move the LH 2nd row seat into easy entry position.
  21. Remove and discard the bolts (x2) that attach the LH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 11mm 소켓
  22. With one hand, engage the towel bar, move the outer seat track rearward with the other hand until the groove on the LH seat podium releases from the outer seat track, and then lift the LH 2nd row seat podium upward while removing it from the inner seat track.
  23. Release the clips (x2) that attach the LH 2nd row EZ entry actuator cable to the RH easy entry latch, and then release the cable from the latch.
  24. Remove the nuts that attach the LH 2nd row seat inner seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 13mm 소켓
  25. Remove the LH 2nd row seat inner seat track from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Slide the outer seat track outwards away from the towel bar.

장착

  1. Position the LH 2nd row seat inner seat track into the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the towel bar spring is in place and the bar is sitting between the tabs.
  2. Install the nuts that attach the LH 2nd row seat inner seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Install outer seat track to seat frame
    팁: 다음 공구 사용을 권장합니다.
    • 13mm 소켓
  3. Secure the clips (x2) that attach the LH 2nd row EZ entry actuator cable to the RH easy entry latch.
  4. Install the groove on the LH 2nd row seat podium to the inner seat track, and then align the groove on the podium to the outer seat track. Engage the towel bar with one hand, and then move the outer seat track inward until the groove on the podium engages to the seat track.
  5. Install new the bolts (x2) that attach the LH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 11mm 소켓
  6. Position the LH 2nd row seat onto the seat tracks, and then push the seat downward to latch the floor latches.
  7. Starting at the rear of the seat, position the LH 2nd row seat pan onto the seat frame.
  8. Install the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    The 10 mm bolts are torqued to 6 Nm. The T25 screws are torqued to 1.5 Nm.
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 소켓
    • Torx T25 소켓
  9. Position the LH 2nd row seat back to the seat assembly, and then install the clips (x4) that attach the seat back to the assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the bottom retainers slide into position.
  10. Install the LH 2nd row seat headrest guide lock. See 가이드 잠금 장치 - 헤드레스트 - 2열(탈거 및 교체).
  11. Install the LH 2nd row headrest adjustment guide. See 조정 가이드 - 헤드레스트 - 2열(탈거 및 교체)
  12. Install the LH 2nd row seat headrest trim. See 헤드레스트 - 2열 - 외측 - LH(탈거 및 교체).
  13. Install the center 2nd row seat back pivot clamps. See 피벗 클램프 - 시트 등받이 - 2열 - 중앙/20(탈거 및 교체).
  14. Install the center 2nd row lumbar bun. See 럼버번 - 2열 - 중앙/20(탈거 및 교체).
  15. Position the LH 2nd row seat outer sideshield to the seat assembly, connect the electrical connector, and then secure the clip.
    Informational PurposesAn informational icon, calling your attention
    참고
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  16. Install the push clip to the front of the LH 2nd row seat outer sideshield assembly.
    팁: Use a pick to remove the push clip from the bottom side of the outboard cover.
  17. Install the clips (x3) that attach the LH 2nd row seat inboard outer trim to the LH 2nd row seat.
  18. Install the center 2nd row seat back panel. See 후면 패널 – 2열 시트 – 중앙/20(5인승)(탈거 및 교체).
  19. Install the LH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - LH(7인승)(탈거 및 교체).
  20. Install the LH 2nd row seat back panel. See 후면 패널 - 2열 시트 - LH(탈거 및 교체).
  21. Install the LH 2nd row seat assembly. See 시트 어셈블리 - 2열 - LH(7인승)(탈거 및 교체).