2024-09-25

Antenna - GPS/GNSS (Remove and Replace)

Correction code 21320102 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-09-12: 카메라 어셈블리에서 하네스를 연결 해제하지 않아도 된다는 참고 사항을 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. 하단 쿼드 카메라 커버를 탈거합니다. 참조 항목: Quad Camera Cover - Lower (Remove and Replace).
  2. 리어 뷰 미러를 탈거합니다. 참조 항목: Mirror - Rear View (Remove and Replace).
  3. 상단 쿼드 카메라 커버를 탈거합니다. 참조 항목: Quad Camera Cover - Upper (Remove and Replace).
  4. 트리플 카메라 후드를 탈거합니다. 참조 항목: Glare Shield (Remove and Replace).
  5. 전방 카메라를 분리합니다. 참조 항목: Camera - Triple - Forward Facing (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    참고
    카메라 어셈블리에서 하네스를 연결 해제하지 않아도 됩니다.
  6. GPS/GNSS 안테나를 브래킷에 고정하는 나사를 탈거하고 안테나를 LH 면으로 밀어 브래킷에서 탭(2개)을 분리한 다음 차량에서 안테나를 탈거합니다.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T10 비트

Install

  1. 안테나를 RH 면으로 밀어 탭(2개)을 고정한 다음 GPS/GNSS 안테나를 브래킷에 고정하는 나사를 장착합니다.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T10 비트
  2. 전방 카메라를 장착합니다. 참조 항목: Camera - Triple - Forward Facing (Remove and Replace).
  3. 트리플 카메라 후드를 장착합니다. 참조 항목: Glare Shield (Remove and Replace).
  4. 상단 쿼드 카메라 커버를 장착합니다. 참조 항목: Quad Camera Cover - Upper (Remove and Replace).
  5. 리어 뷰 미러를 장착합니다. 참조 항목: Mirror - Rear View (Remove and Replace).
  6. 하단 쿼드 카메라 커버를 장착합니다. 참조 항목: Quad Camera Cover - Lower (Remove and Replace).
  7. 전방 카메라를 조정합니다. 참조 항목: Camera - Forward Facing (Pitch Verification).