2021-03-22

Buckle - 3rd Row - LH (Remove and Replace)

Correction code 20058702 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 모든 도어를 열고 모든 창문을 완전히 내립니다.
  2. 전면 좌석을 완전히 앞으로 이동합니다.
  3. 2열 시트를 이지 엔트리 모드로 이동합니다.
  4. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  5. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  6. 3열 시트 쿠션을 탈거합니다. Cushion - Seat - 3rd Row (Remove and Replace)을(를) 참조하십시오.
  7. 3열 시트 중앙 외측 B커버를 중앙 내측 B커버에 고정하는 클립을 분리한 다음 커버를 어셈블리에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    먼저 커버의 상단부에서 분리한 다음 클립을 분리합니다.
  8. 3열 중앙 내측 B커버를 시트 프레임 어셈블리에 고정하는 클립을 탈거합니다.
  9. 3열 중앙 내측 B커버를 시트 프레임 어셈블리에 고정하는 나사를 탈거합니다.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
  10. LH 3열 안전벨트 버클 전기 커넥터를 연결 해제합니다.
  11. LH 3열 안전벨트 버클 전기 커넥터를 시트 프레임 어셈블리에 고정하는 클립을 분리합니다.
  12. LH 3열 안전벨트 버클을 고정하는 볼트를 시트 프레임 어셈블리에서 탈거한 다음 버클을 어셈블리에서 탈거합니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

  1. LH 3열 안전벨트 버클을 시트 프레임 어셈블리에 배치한 다음 볼트를 장착합니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  2. LH 3열 안전벨트 버클 전기 커넥터를 시트 프레임 어셈블리에 고정하는 클립을 조입니다.
  3. LH 3열 안전벨트 버클 전기 커넥터를 연결합니다.
  4. 3열 중앙 내측 B커버를 시트 프레임 어셈블리에 고정하는 클립을 장착합니다.
  5. 3열 중앙 내측 B커버를 시트 프레임 어셈블리에 고정하는 나사를 장착합니다.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
  6. 3열 중앙 외측 B커버를 중앙 내측 B커버에 배치한 다음 외측 커버를 내측 커버에 고정하는 클립을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    먼저 클립을 장착한 다음 커버의 상단부를 고정합니다.
  7. 3열 시트 쿠션을 장착합니다. Cushion - Seat - 3rd Row (Remove and Replace)을(를) 참조하십시오.
  8. 12V 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  9. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  10. 2열 시트를 원래 위치로 이동합니다.
  11. 전면 시트를 원래 위치로 이동합니다.
  12. 모든 창문을 올리고 모든 도어를 닫습니다.