2026-07-31

Coax Cable - Side Repeater - Front - LH (Overlay) (Remove and Replace)

교정 코드 17403012 FRT 1.56 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  • 2026-07-09: Released new procedure.

Overlay

  1. Raise and support the vehicle.
  2. Open both front doors and lower both front windows.
  3. Open the hood.
  4. Remove the rear apron.
  5. Remove HEPA filter assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 5 Nm, Pivot rearward edge up and past brake reservoir, Then lift up to clear frunk assembly, Note: Not all Model Y vehicles have a HEPA filter assembly installed
  6. Remove frunk access panel
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, 3x guide tabs, 1x connector
  7. Remove fasteners securing frunk assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    (*Use this ALL MODELS version of the step for multiple-model type procedures) 5x bolts, 10mm, 5 Nm, Newer vehicles may be equipped with 4x bolts and 1x push clip securing frunk to reservoir neck
  8. Remove clip securing frunk to washer fluid reservoir neck
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  9. Remove frunk assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Replace any clips if broken or missing
  10. Remove the cowl screen. See 패널 - 카울 스크린(탈거 및 교체).
  11. Remove RH mid A pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 1x tab, Release the upper clip then pull mid A pillar upward to remove
  12. Remove clip securing RH lower A pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  13. Remove RH lower A pillar trim to release seat harness.
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips, 2 guide tabs, Pull rear of lower A pillar upward to release clip then pull rearward to release trim panel
  14. Move the RH front seat back.
  15. Remove RH front floor mat
  16. Release RH footwell assembly from IP
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T20, 1.2 Nm, 1x push clip, 8x tabs, carefully pull out to release tabs
  17. Disconnect RH footwell lighting and speaker connectors
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors
  18. Remove RH console side panel carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 1x guide pin, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
  19. Remove clip securing RH front cabin carpet to body
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip
  20. Fold RH front cabin carpet rearward
    Informational PurposesAn informational icon, calling your attention
    참고
    Newer Vins may be equipped with additional foam installed below carpet
  21. Remove LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    참고
    1x cap, Use both hands to gently pull the wheel cap to release the clips, Wheels may be equipped with center caps
  22. Loosen the lug nuts (x5) on the LH front wheel.
  23. Raise vehicle partially and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    참고
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side
  24. Remove the LH front wheel.
  25. Release LH front wheel liner from vehicle and set aside
    Informational PurposesAn informational icon, calling your attention
    참고
    8x clips, 3x tabs, 1x bolt, 10mm, 6 Nm
  26. Disconnect LH side repeater and camera
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, Disengage lock on camera connector
  27. Lower vehicle partially and set lift onto locks
    Informational PurposesAn informational icon, calling your attention
    참고
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  28. Remove fresh air intake duct
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm bolt, 4 Nm, 1x datum, 2x ears, Set ears on bulkhead studs, Secure to thermal bar
  29. Release windshield heater connecter
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  30. Release RH grommet from body
  31. Remove electrical tape securing harness bundle to rubber dust boot
    Informational PurposesAn informational icon, calling your attention
    참고
    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
  32. Remove locking pin from connector
    Informational PurposesAn informational icon, calling your attention
    참고
    Carefully pry pin out of connector and fully remove locking pin
  33. Remove coax cable needed for the side repeater overlay MY terminal 1 (LHS)
    Informational PurposesAn informational icon, calling your attention
    참고
    Inspect all components for damage
  34. Apply harness tape onto LH coax overlay cable before installation
    Informational PurposesAn informational icon, calling your attention
    참고
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  35. Position MY LH coax overlay cable into place, Place through LH wheel liner
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull till you have roughly 12 inches of cable towards the interior of the vehicle
  36. Pull LH coax overlay cable through frunk harness
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull harness towards car computer and grommet, Route under steering electric steering column
  37. Tape coax overlay onto fish nylon tape
  38. Pull LH coax overlay cable through bulkhead and into interior cabin
  39. Remove nylon fish tape
    Informational PurposesAn informational icon, calling your attention
    참고
    Remove tape the pull nylon fish tape out of vehicle
  40. Release side repeater cameras connector X870 from car computer
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Release red tab before removing connector
  41. Remove locking pin from side repeater cameras connector
    Informational PurposesAn informational icon, calling your attention
    참고
    Carefully pry pin out of connector and fully remove locking pin
  42. Remove MY coax terminal 1 (LHS) cable from connector
    Informational PurposesAn informational icon, calling your attention
    참고
    Inspect all components for damage
  43. Insert new side repeater coax terminal 1 (LHS) cable onto side repeater cameras connector
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm
  44. Secure locking pin to connector
    Informational PurposesAn informational icon, calling your attention
    참고
    Align tabs of lock in connector housing, Ensure flush installation of locking pin to connector housing
  45. Install side repeater cameras connector x870 onto car computer
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector
  46. Position MY LH coax overlay cable onto frunk main harness, Secure cable onto harness using zip ties
    Informational PurposesAn informational icon, calling your attention
    참고
    11x zip-ties, Trim off excess material after harness has been secured
  47. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    참고
    Cut the coax connector only
  48. Connect electrical harness to LH side repeater
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, Ensure lock on camera connection is secure
  49. Secure RH grommet from body
    Informational PurposesAn informational icon, calling your attention
    참고
    Use electrical tape to wrap the end of the dust boot
  50. Secure LH front wheel liner onto vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    8x clips, 3x tabs, 1x bolt, 10mm, 6 Nm, Route liner under garnish clips, Align studs then install clips
  51. Install LH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  52. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    참고
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  53. Torque LH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  54. Install LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    참고
    1x cap, Align valve stem with wheel cap cavity
  55. Install the cowl screen. See 패널 - 카울 스크린(탈거 및 교체).
  56. Install fresh air intake duct
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm bolt, 4 Nm, 2x clips, 1x pin, Set clips on bulkhead studs, Secure to thermal bar
  57. Install HEPA filter assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 5 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct, Note: Not all Model Y vehicles have a HEPA filter assembly installed
  58. Install frunk assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, 3x locator pins, Replace any clips if broken or missing
  59. Secure frunk to washer fluid reservoir neck
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  60. Install fasteners securing frunk assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    5x bolts, 10mm, 5 Nm, Newer vehicles may be equipped with 1x push clip securing frunk to washer bottle neck
  61. Install frunk access panel
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, 1x connector
  62. Install the rear apron.
  63. Close the hood.
  64. Fold RH main carpet back in place
  65. Install clip securing RH front cabin carpet to body
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  66. Install RH console side panel carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 1x guide pin, Position side panel and align the locator, then the rear locator, Push side panel towards console to install
  67. Install RH footwell assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors
  68. Secure RH footwell assembly onto IP
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, T20, 1.2 Nm, 1x push clip, 8x tabs, carefully align tabs and push to secure in place
  69. Install RH lower A pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips, 2x locating pins, Align front locating pin first
  70. Install clip securing RH lower A pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip
  71. Install RH mid A pillar assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A pillar, Make sure the seal seat on top of the trim
  72. Move RH front seat to original position
  73. Install RH front floor mat
  74. Clear DAS Calibration through UI
    Informational PurposesAn informational icon, calling your attention
    참고
    Controls > Service > Camera Calibration, Select Clear Calibration, Verify calibration was cleared successfully, Wait for prompt to disappear automatically before continuing, Calibration in Progress message and progress icon will appear during the next drive cycle
  75. Verify operation of windshield washers and wipers
    Informational PurposesAn informational icon, calling your attention
    참고
    Fully press and hold the button on the end of the left-hand steering column lever to spray washer fluid onto the windshield, While spraying the windshield the wipers turn on, After releasing the button the wipers perform two additional wipes then a third wipe a few seconds later
  76. Raise both front windows and close both front doors.