2024-09-09

Link - Compliance - Lower - Front - LH (Remove and Replace)

Correction code 31013602 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-06-29: 보충 목적 전용으로 전체 절차 비디오를 개요로 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Torque Specifications

표 1. Torque Specifications: Link - Compliance - Lower - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 전면 하단 컴플라이언스 링크를 전면 서브프레임에 고정하는 볼트 및 너트
115 Nm (84.8 lbs-ft)
  • 21mm 소켓
Reuse
LH 전면 하단 컴플라이언스 링크를 너클에 고정하는 너트
180 Nm (132.7 lbs-ft)
  • 22mm 소켓
  • Torx T45 소켓
Replace 1109263-00-B 또는 그 이상

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. LH 전면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  3. 전면 에어로 실드를 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  4. LH 전면 하단 컴플라이언스 링크를 전면 서브프레임에 고정하는 볼트 및 너트를 탈거합니다.
    115 Nm (84.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21mm 소켓
  5. LH 전면 하단 컴플라이언스 링크를 너클에 고정하는 너트를 탈거하여 폐기한 다음 차량에서 링크를 탈거합니다.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    T45 소켓으로 스터드를 반대쪽에서 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 22mm 소켓
    • Torx T45 소켓

Install

  1. LH 전면 하단 컴플라이언스 링크를 전면 서브프레임에 배치한 다음 링크를 서브프레임에 고정하는 볼트 및 너트를 장착합니다.
    115 Nm (84.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21mm 소켓
  2. LH 전면 하단 컴플라이언스 링크를 너클에 고정하는 새 너트를 장착합니다.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    T45 소켓으로 스터드를 반대쪽에서 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 22mm 소켓
    • Torx T45 소켓
  3. 전면 에어로 실드를 장착합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  4. LH 전면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  5. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.
  6. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See 얼라인먼트 요구 사항 - 서스펜션.