31/10/2022 01:06:08

주물 - 포디엄 - 2열 시트 - LH(7인승)(탈거 및 교체)

교정 코드 13020132 0.36 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

탈거

  1. Remove the LH 2nd row seat assembly from the vehicle. See 시트 어셈블리 - 2열 - LH(7인승)(탈거 및 교체).
  2. Remove the push clip from the front of the LH 2nd row seat outer sideshield assembly.
    팁: Use a pick to remove the push clip from the bottom side of the outboard cover.
  3. Release the clip that attaches the LH 2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector, and then remove the sideshield from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  4. Release the clips (x3) that attach the LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from the seat assembly.
  5. Remove the seat pan fastener from the LH front of the LH 2nd row seat.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    1x fastener,10mm, 6Nm
    팁: 다음 공구 사용을 권장합니다.
    • 10 mm socket
  6. Release the clips (x2) that attach the front of the LH 2nd row seat cushion to the seat assembly, and then lift the front edge of the seat cushion to access the podium fasteners.
  7. Remove and discard the bolts (x2) and release the harness clip that attach the LH 2nd row seat podium casting to the seat assembly, and then remove the casting from the seat assembly.
    37 Nm (27.3 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 11 mm socket

장착

  1. Position the LH 2nd row seat podium casting into the seat assembly, and then secure the harness clip and install new bolts (x2) that attach the casting to the seat assembly.
    37 Nm (27.3 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 11 mm socket
  2. Position the front edge of the LH 2nd row seat cushion onto the seat assembly, and then install the clips that attach the cushion to the seat assembly.
  3. Install the seat pan fastener to the LH front of the LH 2nd row seat.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    1x fastener,10mm, 6Nm
    팁: 다음 공구 사용을 권장합니다.
    • 10 mm socket
  4. Position the LH 2nd row seat outer sideshield to the seat assembly, connect the electrical connector, and then secure the clip that attaches the sideshield to the seat assembly.
  5. Install the push clip at the front of the LH 2nd row seat outer sideshield assembly.
  6. Position the LH 2nd row seat inboard outer trim onto the seat assembly, and then secure the clips (x3) that attach the trim to the seat assembly.
  7. Install the LH 2nd row seat assembly. See 시트 어셈블리 - 2열 - LH(7인승)(탈거 및 교체).