2022-08-26

Hinge - Door - Front - Lower - LH (Remove and Replace)

Correction code 11336602 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1588903-00-A 차체 간격 및 단차 도구
  • 1079485-00-A 크로우풋 오픈 엔드 세트

Remove

  1. LH 전면 도어를 엽니다.
  2. LH 전면 윈도우를 내립니다.
  3. 잭을 사용하여 바닥에서 LH 전면 도어를 지지합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    부드러운 재질을 사용하여 도어의 도장을 보호하십시오.
  4. 장착 도중 정렬에 도움이 되도록 차체 및 도어의 LH 전면 도어 하단 힌지 주변 영역에 마스킹 테이프를 부착합니다.
  5. LH 전면 도어 하단 힌지를 차체에 고정하는 볼트(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 콤비네이션 렌치
  6. LH 전면 도어 하단 힌지를 도어에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 콤비네이션 렌치
  7. 차량에서 LH 전면 도어 하단 힌지를 주의하여 탈거합니다.

Install

  1. 새 LH 전면 하단 힌지를 장착합니다.
  2. LH 전면 도어 하단 힌지를 도어에 고정하는 볼트를 손으로 조입니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 콤비네이션 렌치
  3. LH 전면 도어 하단 힌지를 차체에 고정하는 볼트(2개)를 손으로 조입니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 콤비네이션 렌치
  4. LH 전면 도어를 닫고 간격 및 단차를 점검합니다. 필요 시 조정합니다.
  5. LH 전면 도어 하단 힌지를 도어에 고정하는 볼트를 조입니다.
    49 Nm (36.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  6. LH 전면 도어 하단 힌지를 차체에 고정하는 볼트(2개)를 조입니다.
    24 Nm (17.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  7. 차체 및 도어의 LH 전면 도어 하단 힌지를 둘러싸는 마스킹 테이프를 제거합니다.
  8. LH 전면 도어에서 지지대를 탈거합니다.
  9. 필요한 경우 LH 전면 하단 도어 힌지 볼트에 터치업 페인트를 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    도포하기 전에 터치업 페인트를 흔들고 2차 코트를 도포하기 전에 1차 코트가 완전히 건조될 때까지 20분 이상 기다립니다.
  10. LH 전면 창문을 올립니다.
  11. LH 전면 도어를 닫습니다.