2022-12-13

Recliner Actuator - Seat Back - 2nd Row - LH (Remove and Replace)

Correction code 13053302 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

토크 규격

표 1. Torque Specifications: Recliner Actuator - Seat Back - 2nd Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
2열 중앙/20 럼버 번을 2열 시트에 고정하는 나사
1.5 Nm (1.1 lbs-ft)
  • Torx T20 소켓
Reuse
액추에이터 팬에서 LH 2열 시트 등받이 리클라이너 액추에이터를 고정하는 나사
2.5 Nm (1.8 lbs-ft)
  • 8mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 4개 도어를 모두 열고 모든 창문을 완전히 내립니다.
  2. 전면 좌석을 완전히 전방으로 이동합니다.
  3. 2열 하단 시트 쿠션을 탈거합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  4. LH 후면 도어 씰을 부분적으로 탈거합니다.
  5. LH 후면 실 트림을 탈거합니다. Trim - C-Pillar - Lower - LH (Remove and Replace)을(를) 참조하십시오.
  6. 60 시트 프레임을 차체에 고정하는 패스너를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트 5개, 11mm, 37Nm. 하부 시트 볼트는 메인 카펫 뒤에 있습니다.
  7. 60 시트 등받이 어셈블리를 아래로 접습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    시트 등받이에 추가적인 무게를 가하지 마십시오. 그러는 경우 시트 프레임 정렬 탭이 손상될 수 있으며, 이로 인해 60:40 시트 등받이 사이가 균일하지 않게 될 수 있습니다.
  8. LH 2열 시트 등받이 패널을 탈거합니다. Back Panel – 2nd Row Seat – LH (Remove and Replace)을(를) 참조하십시오.
  9. 차량에서 2열 60 시트 어셈블리를 탈거하고 시트가 아래로 접힌 채로 둡니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    보조 작업자가 있는 것이 좋습니다. 시트를 위로 접지 마십시오.
  10. 후드 받침대로 60 시트를 부분적으로 위쪽으로 고정하되 시트 잠금장치를 체결하지 않습니다.
  11. 클립을 분리하고 중앙 2열 내측 B커버를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    푸시 클립 1개, 추가적인 접근이 필요한 경우 시트를 위로 접되 시트를 위쪽으로 고정하지 마십시오.
  12. 60 시트 프레임 클립에서 액추에이터 케이블을 분리한 다음 케이블을 시트 프레임 래치에서 떨어지게 위로 들어서 분리합니다.
  13. 60 시트 리클라이너 액추에이터 커넥터를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터 1개
  14. 액추에이터 팬에서 60 시트 등받이 리클라이너 액추에이터를 고정하는 나사(2개)를 탈거합니다.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

Installation procedure is the reverse of removal.