28/02/2023 18:44:35
쿠션 팬 - 2열 시트 - LH(7인승)(탈거 및 교체)
교정 코드 13050132 0.54 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.
탈거
- Remove the LH 2nd row seat assembly from the vehicle. See 시트 어셈블리 - 2열 - LH(7인승)(탈거 및 교체).
-
Remove the push clip from the front of
the LH 2nd row seat outer sideshield assembly.
팁: Use a pick to remove the push clip from the bottom side of the outboard cover.
-
Release the clip that attaches the LH
2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector,
and then remove the sideshield from the seat assembly.
참고Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
-
Release the clips (x3) that attach the
LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from
the seat assembly.
- Remove the LH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - LH(7인승)(탈거 및 교체).
- Remove the LH 2nd row seat back panel. See 후면 패널 - 2열 시트 - LH(탈거 및 교체).
- Remove the center 2nd row seat back panel. See 후면 패널 – 2열 시트 – 중앙/20(5인승)(탈거 및 교체).
-
Disconnect the LH 2nd row seat harness
electrical connectors (x7), and then release the clip that attaches the harness to the
seat frame.
-
Release the seat cables (x4) from the
LH 2nd row seat EZ entry actuator.
-
Release the clip that attaches the
cable to the LH 2nd row seat fold actuator.
-
Remove the push clips (x2) from the LH
2nd row seat cushion pan.
- Remove the center 2nd row lumbar bun. See 럼버번 - 2열 - 중앙/20(탈거 및 교체).
- Remove the center 2nd row seat back pivot clamps. See 피벗 클램프 - 시트 등받이 - 2열 - 중앙/20(탈거 및 교체).
-
Lift the center 2nd row seat back
upward to remove it from the seat assembly.
-
Manually release the center seatback
latch.
참고Use a small screwdriver to manipulate the center seatback latch to release it.
-
Remove the fasteners (x4) that attach
the LH 2nd row seat seat pan to the seat frame.팁: 다음 공구 사용을 권장합니다.
- 10mm 소켓
- Torx T25 소켓
- Remove the LH 2nd row seat headrest trim. See 헤드레스트 - 2열 - 외측 - LH(탈거 및 교체).
- Remove the LH 2nd row headrest adjustment guide. See 조정 가이드 - 헤드레스트 - 2열(탈거 및 교체)
- Remove the LH 2nd row seat headrest guide lock. See 가이드 잠금 장치 - 헤드레스트 - 2열(탈거 및 교체).
-
Release the clips (x4) that attach the
LH 2nd row seat back to the seat assembly, and then lift the seat back to remove it from
the assembly.
-
Lift the rear of the LH 2nd row seat
cushion assembly, and then slide the cushion toward the front of the seat to remove it
from the seat assembly.
-
Disconnect the remaining connectors
(x4) from the LH 2nd row seat cushion pan.
-
Release the J-hooks that attach the LH
2nd row seat cushion cover from the cushion pan, and then remove the cover from the
cushion pan.
-
Disconnect the LH 2nd row seat fold
actuator connector.
-
Disconnect the actuator switch box
connector.
-
Release the remaining seat harness
clips (x4) from the LH 2nd row seat cushion pan.
-
Remove the bolts that attach the LH
2nd row seat fold actuator to the cushion pan, and then remove the actuator from the
cushion pan.팁: 다음 공구 사용을 권장합니다.
- 8mm 소켓
-
Remove the bolts (x6) that attach LH
2nd row seat actuator switch box to the cushion pan, and then remove the switch box, EZ
entry latch, and floor latch actuators from the cushion pan.팁: 다음 공구 사용을 권장합니다.
- 8mm 소켓
장착
-
Position the LH 2nd row seat actuator
switch box, EZ entry latch, and floor latch actuators to the cushion pan, and then
install the bolts (x6) that attach the switch box to the cushion pan.팁: 다음 공구 사용을 권장합니다.
- 8mm 소켓
-
Position the LH 2nd row seat fold
actuator to the cushion pan, and then install the bolts that attach the actuator to the
cushion pan.팁: 다음 공구 사용을 권장합니다.
- 8mm 소켓
-
Secure the seat harness clips (x4) to
the LH 2nd row seat cushion pan.
-
Connect the LH 2nd row seat fold
actuator connector.
-
Connect the actuator switch box
connector.
-
Position the LH 2nd row seat cushion
cover onto the cushion pan, and then secure the J-hooks that attach the cover to the
cushion pan.
-
Starting at the rear of the seat,
position the LH 2nd row seat pan onto the seat frame.
-
Install the fasteners (x4) that attach
the LH 2nd row seat seat pan to the seat frame.참고The 10 mm bolts are torqued to 6 Nm. The T25 screws are torqued to 1.5 Nm.팁: 다음 공구 사용을 권장합니다.
- 10mm 소켓
- Torx T25 소켓
-
Position the LH 2nd row seat back to
the seat assembly, and then install the clips (x4) that attach the seat back to the
assembly.
참고Make sure the bottom retainers slide into position.
- Install the LH 2nd row seat headrest guide lock. See 가이드 잠금 장치 - 헤드레스트 - 2열(탈거 및 교체).
- Install the LH 2nd row headrest adjustment guide. See 조정 가이드 - 헤드레스트 - 2열(탈거 및 교체)
- Install the LH 2nd row seat headrest trim. See 헤드레스트 - 2열 - 외측 - LH(탈거 및 교체).
- Install the center 2nd row seat back pivot clamps. See 피벗 클램프 - 시트 등받이 - 2열 - 중앙/20(탈거 및 교체).
- Install the center 2nd row lumbar bun. See 럼버번 - 2열 - 중앙/20(탈거 및 교체).
-
Position the LH 2nd row seat outer
sideshield to the seat assembly, connect the electrical connector, and then secure the
clip.
참고Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
-
Install the push clip to the front of
the LH 2nd row seat outer sideshield assembly.
팁: Use a pick to remove the push clip from the bottom side of the outboard cover.
-
Install the clips (x3) that attach the
LH 2nd row seat inboard outer trim to the LH 2nd row seat.
- Install the center 2nd row seat back panel. See 후면 패널 – 2열 시트 – 중앙/20(5인승)(탈거 및 교체).
- Install the LH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - LH(7인승)(탈거 및 교체).
- Install the LH 2nd row seat back panel. See 후면 패널 - 2열 시트 - LH(탈거 및 교체).
- Install the LH 2nd row seat assembly. See 시트 어셈블리 - 2열 - LH(7인승)(탈거 및 교체).