2024-12-01

Harness - HVAC Assembly (Remove and Replace)

Correction code 17104102 3.00 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-04-05: A/C 오일 규격에 대한 유액 및 용량을(를) 참조하여 사용할 A/C 오일 유형을 업데이트했습니다.
Informational PurposesAn informational icon, calling your attention
참고
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Torque Specifications

표 1. Torque Specifications: Harness - HVAC Assembly (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 및 RH 블리드 액추에이터를 HVAC 어셈블리에 고정하는 볼트(4개)
2.3 Nm (1.7 lbs-ft)
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 4인치 익스텐션
  • 6mm 소켓
Reuse

Remove

  1. HVAC 어셈블리를 탈거합니다. 참조 항목: HVAC Assembly (Remove and Replace).
  2. 흡기 액추에이터 커넥터를 연결 해제합니다.
  3. 상단 모드 액추에이터 커넥터를 연결 해제합니다.
  4. RH 상단 덕트 서미스터 커넥터를 연결 해제합니다.
  5. RH 하단 덕트 서미스터 커넥터를 연결 해제합니다.
  6. 하단 모드 액추에이터 커넥터를 연결 해제합니다.
  7. RH 블리드 액추에이터 커넥터를 연결 해제합니다.
  8. LH 블리드 액추에이터 커넥터를 연결 해제합니다.
  9. LH 증발기 서미스터 커넥터를 연결 해제합니다.
  10. LH 상단 덕트 서미스터 커넥터를 연결 해제합니다.
  11. LH 하단 덕트 서미스터 커넥터를 연결 해제합니다.
  12. LH 및 RH 블리드 액추에이터를 HVAC 어셈블리에 고정하는 볼트(4개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
    • 6mm 소켓
  13. HVAC 어셈블리의 RH에서 클립(3개)을 분리합니다.
  14. RH 고정 탭(3개)에서 HVAC 하네스를 분리합니다.
  15. 상단 고정 탭(2개)에서 HVAC 하네스를 분리합니다.
  16. LH 고정 탭(4개)에서 HVAC 하네스를 분리한 다음 HVAC 어셈블리에서 HVAC 하네스를 탈거합니다.

Install

  1. HVAC 하네스를 HVAC 어셈블리에 배치하고 LH 증발기 서미스터를 연결합니다.
  2. LH 상단 덕트 서미스터 커넥터를 연결합니다.
  3. LH 하단 덕트 서미스터 커넥터를 연결합니다.
  4. LH 고정 탭(4개)에 HVAC 하네스를 장착합니다.
  5. 상단 고정 탭(2개)에 HVAC 하네스를 장착합니다.
  6. 하단 모드 액추에이터 커넥터를 연결합니다.
  7. 상단 모드 액추에이터 커넥터를 연결합니다.
  8. 흡기 액추에이터 커넥터를 연결합니다.
  9. RH 하단 덕트 서미스터 커넥터를 연결합니다.
  10. RH 상단 덕트 서미스터 커넥터를 연결합니다.
  11. HVAC 어셈블리의 RH에서 클립(3개)을 장착합니다.
  12. RH 고정 탭(3개)에 HVAC 하네스를 장착합니다.
  13. LH 및 RH 블리드 액추에이터를 HVAC 어셈블리에 고정하는 볼트(4개)를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
    • 6mm 소켓
  14. RH 블리드 액추에이터 커넥터를 연결합니다.
  15. LH 블리드 액추에이터 커넥터를 연결합니다.
  16. HVAC 어셈블리를 장착합니다. 참조 항목: HVAC Assembly (Remove and Replace).