10/12/2024 06:58:25

버클 - 2열 - 중앙(7인승)(탈거 및 교체)

교정 코드 20057222 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

  • 2023-06-06: Added torque specifications and fixed missing/incorrect steps.
  • 2023-05-10: Rearranged procedure steps and added configuration instructions.
  • 2024-11-26: Add a note to clarify that harness should not be around bolt when install the buckle to seat assembly.

탈거

  1. Open the rear doors and lower the rear windows.
  2. Remove the LH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - LH(7인승)(탈거 및 교체).
  3. Disconnect center 2nd row buckle electrical connector, and then release the connector from the seat assembly.
  4. Return the LH 2nd row seat to its original position.
  5. Move the RH 2nd row seat forward.
  6. Release the tabs (x4) that attach the RH 2nd row seat back inboard cover to the seat assembly.
    팁: Release the front portion first, and then slide the cover straight rearward to clear the groove.
  7. Release the edge clip that attaches the cushion cover to the seat back assembly.
  8. Release the 2nd row center buckle harness from the LH seat back assembly.
  9. Remove and discard the bolt that attaches the center 2nd row buckle to the seat assembly, and then remove the buckle from the assembly.
    40 Nm (29.5 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 15mm 소켓

장착

  1. Position the center 2nd row buckle to the seat assembly, and then install a new bolt that attaches the buckle to the assembly.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure to not pinch the wire between the bolt and the buckle bracket. Harness should not be around bolt.
    팁: 다음 공구 사용을 권장합니다.
    • 15mm 소켓
  2. Install the center buckle harness onto the LH seat back assembly.
  3. Install the edge clip that attaches the cushion cover to the LH 2nd row seat back assembly.
  4. Position the LH 2nd row seat back inboard cover onto the seat assembly, slide the cover forward into the grooved section, and then secure the tabs (x4).
  5. Move the LH 2nd row seat forward.
  6. Install the center 2nd row buckle connector onto the seat assembly, and then connect the connector.
  7. Install the LH 2nd row seat toe kick cover. See 커버 - 토우 킥 - 2열 시트 - LH(7인승)(탈거 및 교체).
  8. Move the 2nd row seats to the original positions.
  9. Raise rear windows and close rear doors.