2025-06-27

Buckle - 2nd Row - Center (5 Seat) (Remove and Replace)

Correction code 20057202 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-11-26: 버클을 시트 쿠션 프레임에 장착할 때 볼트 주위에 하네스가 있으면 안 된다는 점을 명확히 설명하는 참고 사항을 추가합니다.
  • 2152873-00-A 도구, 유도성 가열

Torque Specifications

표 1. Torque Specifications: Buckle - 2nd Row - Center (5 Seat) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
중앙 버클을 LH 하단 시트 쿠션 프레임에 고정하는 볼트
40 Nm (29.5 lbs-ft)
  • Torx T50 소켓
Replace

Remove

  1. 모든 도어를 열고 모든 창문을 완전히 내립니다.
  2. 2열 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  3. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace)
  4. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. RH 하단 C필러 트림을 탈거합니다. 참조 항목: Trim - C-Pillar - Lower - LH (Remove and Replace).
  6. RH 2열 시트 등받이/시트 프레임 어셈블리를 탈거합니다. 참조 항목: Seat Back - 2nd Row - RH (Remove and Replace).
  7. 중앙 버클 커넥터를 LH 하단 시트 쿠션 프레임에 고정하는 클립을 탈거합니다.
  8. LH 시트 프레임 하네스에서 중앙 버클 커넥터를 탈거합니다.
  9. 중앙 버클을 LH 하단 시트 쿠션 프레임에 고정하는 볼트를 탈거한 다음 어셈블리에서 중앙 버클을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓

Install

  1. LH 중앙 2열 버클을 차량에 배치한 다음 버클을 시트 쿠션 프레임에 고정하는 볼트를 장착합니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트와 버클 브래킷 사이에 와이어가 끼지 않도록 주의하십시오. 볼트 주위에 하네스가 없어야 합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
  2. LH 시트 프레임 하네스에 중앙 버클 커넥터를 연결합니다.
  3. 중앙 버클 커넥터를 LH 하단 시트 쿠션 프레임에 고정하는 클립을 장착합니다.
  4. RH 2열 시트 등받이를 장착합니다. 참조 항목: Seat Back - 2nd Row - RH (Remove and Replace).
  5. RH 하단 C필러 트림을 장착합니다. 참조 항목: Trim - C-Pillar - Lower - LH (Remove and Replace).
  6. 2열 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  7. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  8. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace)
  9. 전면 시트를 원래 위치로 이동합니다.
  10. Toolbox 3가 설치된 노트북을 차량에 연결합니다.
  11. Toolbox에서 Actions 탭을 클릭하고 검색 필드에 "vcleft rear seat cushion"을 입력한 후 TEST-SELF_VCLEFT_REAR_SEATvia Toolbox: (link)을(를) 클릭하고 Run을 클릭한 다음 루틴이 완료될 때까지 기다립니다.
  12. Toolbox를 연결 해제하고 차량에서 노트북을 탈거합니다.
  13. 모든 창문을 올리고 모든 도어를 닫습니다.