2024-06-04

Center Console (Remove and Replace)

Correction code 15190102 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

토크 규격

표 1. Torque Specifications: Center Console (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
보안 차체 컨트롤러를 컵 홀더 장식 패널에 고정하는 나사
1.6 Nm (1.2 lbs-ft)
  • Torx T20 소켓
Reuse
센터 콘솔 브라이트 스트립을 센터 콘솔 어셈블리에 고정하는 나사(4개)
1.6 Nm (1.2 lbs-ft)
  • Torx T20 소켓
Reuse

Remove

Informational PurposesAn informational icon, calling your attention
참고
현재 차량에 탑재되어 있는 보안 컨트롤러(SEC)를 교체하는 센터 콘솔로 옮깁니다. 이는 차량/키의 재구성 없이 작동할 수 있습니다.
  1. 센터 콘솔 어셈블리를 탈거합니다. 참조 항목: Center Console (Remove and Install).
  2. LH 장식 트림의 후면을 센터 콘솔 어셈블리에 고정하는 클립(4개)를 분리합니다.
  3. LH 센터 콘솔 브라이트 스트립을 센터 콘솔 어셈블리에 고정하는 나사(4개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  4. LH 센터 콘솔 브라이트 스트립을 센터 콘솔 어셈블리에 고정하는 탭(3개)을 분리한 후, 어셈블리에서 브라이트 스트립을 부분적으로 분리합니다.
  5. 센터콘솔의 RH 쪽에 대해 2 단계부터 4 단계를 반복합니다.
  6. 컵 홀더 장식 패널을 컵 홀더 어셈블리에 고정하는 클립(6개)을 분리한 다음, 센터 콘솔 어셈블리에서 컵 홀더 장식 패널을 분리합니다.
  7. 보안 차체 컨트롤러 모듈에서 전기 커넥터를 연결 해제한 다음, 차량에서 컵 홀더 장식 패널을 탈거합니다.
  8. 보안 차체 컨트롤러 모듈을 컵 홀더 장식 패널에 고정하는 나사(2개)를 탈거한 다음 패널에서 보안 차체 컨트롤러 모듈을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  9. 새 센터콘솔 어셈블리에 대해 2 단계부터 7 단계를 반복합니다.

Install

  1. 새 컵 홀더 장식 패널에 보안 컨트롤러(SEC)를 배치한 후, 컨트롤러를 패널에 고정하는 나사를 장착합니다.
    1.6 Nm (1.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  2. 전기 커넥터를 보안 차체 컨트롤러 모듈에 연결합니다.
  3. 컵 홀더 장식 패널을 센터 콘솔 어셈블리에 고정하는 클립(6개)을 고정합니다.
  4. RH 센터 콘솔 브라이트 스트립을 센터 콘솔 어셈블리에 장착합니다.
  5. RH 센터 콘솔 브라이트 스트립을 센터 콘솔 어셈블리에 고정하는 나사(4개)를 장착합니다.
    1.6 Nm (1.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  6. 센터 콘솔 어셈블리에 RH 장식 트림을 장착합니다.
  7. 센터 콘솔의 LH에 대해 4단계~6단계를 반복합니다.
  8. 센터 콘솔 어셈블리를 장착합니다. 참조 항목: Center Console (Remove and Install).