2025-03-14

Buckle - 2nd Row - LH (5 Seat) (Remove and Replace)

Correction code 20057002 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-11-26: 버클을 시트 어셈블리에 장착할 때 볼트 주위에 하네스가 있으면 안 된다는 점을 명확히 설명하는 참고 사항을 추가합니다.

Torque Specifications

표 1. 토크 규격: Buckle - 2nd Row - LH (5 Seat) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 버클을 차체에 고정하는 볼트
40 Nm (29.5 lbs-ft)
  • Torx T45 소켓
Replace 볼트는 버클 어셈블리에 고정됨

Remove

  1. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  2. 12V 전원을 연결 해제합니다. 참조 항목: Disconnect (납산 배터리가 있는 Model Y).
  3. 클립 프라이툴을 사용하여 LH 2열 버클을 시트 프레임에 고정하는 클립을 풉니다.
  4. LH 2열 버클 전기 커넥터를 연결 해제합니다.
  5. LH 2열 버클을 시트 프레임에 고정하는 고정 볼트를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Torx T45 소켓

Install

  1. 고정 볼트를 조여 LH 2열 버클을 시트 프레임에 장착합니다.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    볼트와 버클 브래킷 사이에 와이어가 끼지 않도록 주의하십시오. 볼트 주위에 하네스가 없어야 합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Torx T45 소켓
  2. LH 2열 버클 전기 커넥터를 연결합니다.
  3. LH 2열 버클을 시트 프레임에 고정하는 클립을 고정합니다.
  4. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  5. 12V 전원을 연결합니다. 참조 항목: Connect (납산 배터리가 있는 Model Y).
  6. Toolbox 3.0를 사용하여 차량에 연결합니다.
  7. Toolbox에서 검색 필드에 "vcleft rear seat cushion"을 입력합니다.
  8. TEST-SELF_VCLEFT_REAR_SEATvia Toolbox: (link)을(를) 선택한 다음 "Run"을 클릭합니다.
  9. 차량에서 노트북을 연결 해제합니다.